Replacement Gears for Bulldog Sidewind Trailer Jacks with 5,000-lb Capacity

See what our Experts say about this Bulldog Accessories and Parts

• How to Determine the Correct Sidewind Gear Kit to Replace Roll Pins for Gears in a Bulldog Jack
  There are two possibilities for your Bulldog Trailer Jack. The Replacement Sidewind Gear Kit, item # BD5002581360, is designed for jacks with a 5/8 inch diameter inside bottom gear. The Replacement Sidewind Gear Kit, item # BD500156, is designed for jacks that have a 1/2 inch inside bottom gear. You will need to measure the overall diameter of the bottom gear of your jack to get the correct kit.
  view full answer...
• Replacement Gear Kit For Older Fulton Square Tube Weld On Jack
  We do offer replacement parts for Fulton jacks, including the square tube type. These parts are not always a universal fit, so you will need to order replacement parts that are rated correctly for your particular Fulton jack. If you can find a model number somewhere on the jack it would really help to narrow it down. For example the Fulton gear kit # F0933302S00 comes with a 12 tooth gear and fits a variety of Fulton marine and recreational Jacks, mainly their FXP10 model jacks. If you...
  view full answer...
• Replacement Washer With Hex Pattern For Handle on Fulton Marine Jack # HD50000101
  You are needing the Replacement Sidewind Gear Kit # BD5002581360 which will include the hex pattern thrust washer for the handle side of your Fulton Marine Jack # HD50000101.
  view full answer...
• Should a Bulldog Series 190 Sidewind Jack that is Not Working be Repaired or Replaced
  There can be many reasons a trailer jack might bind and cause the center pin to be sheared off from the handle. The more common causes is if the jack is overloaded, if the lower inner tube is bent, or if debris has gotten into the gears or bearing. To determine if you can just replace the inner parts and use your existing jack, you will want to inspect the whole jack to make sure everything is structurally sound and the lower tube is not bent. If the lower tube is bent I would recommend...
  view full answer...
• 5K Capacity Bulldog Jack Is Jammed and Will Not Raise or Lower Trailer
  According to Bulldog, the jack has been either over extended or retracted and the main screw inside that runs the jack in and out has jammed into the nut. If using a reasonable amount of force won't successfully retract or extend the jack, then Bulldog recommends that the jack be replaced as the screw has been damaged and a replacement part isn't available. The closest replacement to your original jack is part # PS1400800383.
  view full answer...
  
• Solution for Replacement Gears for Discontinued Atwood Sidewind Jack
  Atwood jacks are no longer being produced which means replacement parts like gears are no longer available. The # BD5002581360 you looked at does have similar dimensions for the large gear, but it is designed for Bulldog jacks not Atwood. I understand you want to repair this rather than replace it, but more than likely replacement is the only option. You could try to find an old jack at a junk yard and pull gears out of it but that's a long shot. If you can't find anything then you could...
  view full answer...
• Will Replacement Sidewind Gear Kit for 7,000 Pound Bulldog Jacks fit my 190 Series Bulldog Jack
  Yes, the Replacement Gear Kit, part BD5002581360, is made to be used with Bulldog series 190 jacks.
  view full answer...
• Replacement Gear Set For Bulldog 190784 5,000LB Trailer Jack
  Yes, the Replacement Gears # BD5002581360 will fit your Bulldog Jack 190784. This kit is specific to the 190 series jacks up to and including 5,000lb lift capacities.
  view full answer...
  
• Bulldog Round Sidewind Jack Replacement Handle Up to 5,000lbs
  Yes, Replacement Sidewind Handle # BD500105 will be the correct replacement for your Bulldog Jack assuming it is below 5,000lbs capacity. I would also recommend inspecting the gears and replacing those if they show signs of excessive wear or damage. Replacement Sidewind Gear Kit # BD5002581360 will be the one you need if required.
  view full answer...
• Will the Replacement Sidewind Handle for Bulldog Round or Square Jacks fit on a 7,000 pound Jack
  To determine the correct jack handle and gears for your Bulldog 7,000 lbs. jack, I will need to know the model number of your jack to help determine the correct parts. If your jack is similar to the Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15 inch Lift - 7,000 lbs, item # BD198250, with the top mount gear box, the correct handle will be the Sidewind Handle for Bulldog Square Jacks, item # BD500171. There are two possible sets of gears that could fit your jack and you will need...
  view full answer...
• What is the Inner Diameter of Replacement Bearing for Bulldog Square Jacks, # BD001015
  I spoke with my contact at Bulldog regarding the Replacement Bearing for Bulldog Square Jacks, # BD001015. He stated that the inside diameter is 0.876 inches. This is 1 thousand of an inch larger than 7/8 inches. The outer diameter is 2 inches. We carry several other replacement gears for Bulldog jacks including # BD500106, # BD5002581360, # BD500156, and # BD500212.
  view full answer...
• How to Remove Handle from 8k Square Bulldog Jack
  I spoke to my contact at Bulldog and he told me that the pin you are trying to get out is a 5/32 grooved pin that will need to be tapped out with a punch like you mentioned. It's designed not to come out so you will need to hit it pretty hard. Once you get the pin out the handle will come off.
  view full answer...

Do you have a question about this Accessories and Part?