Customers compare TTRA1702 to these similar products
Products Featured in this Video
Speaker 1: Today we're going to take a look at the Timbren Trailer Suspension Enhancement System for light duty trailers. It has a 1,000 pound weight capacity. Now this part will improve suspension, handling and safety of your utility or camping trailer. This will provide additional support as needed, so you always have a nice smooth, comfortable ride. It will allow the leaf spring ample… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
The Timbren Trailer Suspension Enhancement System #TTRA1702 is 2-3/4" tall with no load on the spring. This particular system is designed to mount to the frame with the included bracket(see image) and when the suspension compresses the axle…
view full answer...The Timbren Trailer Suspension Enhancement System Light-Duty Trailers 1,000 lbs #TTRA1702 will be a great help in reducing body roll and helping dampen the bounce. Based on your measurements this will immediately take on load and stabilizing while…
view full answer...For suspension enhancement on your trailer you'll want a Timbren spring for trailers like #TTRA1702 which measure 2-3/4 inches high. I've also linked our selection of Timbren springs for trailers for you.
view full answer...We don't offer airbags, like what is normally installed on a tow vehicle, for trailers. We do have jounce-style helper springs that may work for you. The Timbren Trailer Suspension Enhancement System #TTRA1702 install onto your trailer's…
view full answer...Usually when a trailer is bouncing around a lot behind tow vehicle, it starts with an improperly loaded trailer that has too much tongue weight and weight that is not properly distributed. Typically a trailer should have 10-15% of the total weight on…
view full answer...The Timbren Trailer Suspension Enhancement System, part #TTRA1702 is designed for light duty trailers. This system has a weight capacity of 1,000 lbs. You do not want to exceed the trailers weight carrying capacity. Also, this system is for trailers…
view full answer...The Timbren Trailer Suspension Enhancement System #TTRA1702 doesn't have to fit between the u-bolts of the trailer axle. All that is required is that the plate attaches to the frame and the rubber spring touches the axles so you could mount is so…
view full answer...It sounds like you may need to look into the state of the suspension on your trailer. If there is so much movement that it has caused the tires to damage the fenders then something is not quite right. The Timbren springs like #TTRA1702 are designed…
view full answer...Unfortunately Timbren does not make their Timbren Active Off-Road Bumpstops #TABSOSR kit without the axle bracket, so if you don't need it you'll just ignore it and install everything else. To figure out if you need a spacer kit #T68MR…
view full answer...I went out to the warehouse and pulled the Replacement Square-Bar Clamp-On for Thule Ride-On Adapter #853-2156 and found that it is 1-1/8" wide by 1" tall and the Thule Square Bar Adapter for Fairing #853-7362 is 1-7/16" wide by…
view full answer...For the Thule Force XT Sport Rooftop Cargo Box #TH6356B to allow the hatch on your 2016 Honda CR-V to fully open without interference you need to have at least 48-1/4" from the middle of your forward most crossbar to the line where your roof and…
view full answer...I do have an option for you but the Lippert Components Bolt-On Shock Kit like part #LC281281 is designed for use on overslung axles (leaf springs over axle) only. Therefore, it should not be used with the underslung (leaf springs under axle) axles…
view full answer...