Customers compare STL70RB to these similar products
Products Featured in this Video
Today we are looking at the Optronics Sealed, 6-1/2 inches Oval LED Trailer Stop, Turn and Tail Light, part number STL70RB. This light functions as a stop, turn and tail light. It has a sealed waterproof housing and lens unit. This light comes with 48 LEDs or light emitting diodes. It flush mounts with a mounting grommet and plug which are required to complete the installation, but sold… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
The Optronics light that you referenced, part #ST70RB, is an exact replacement for Bargman light #40-06-001. If you can find that part number on your Bargman light, then we can be sure that this light is the correct replacement. Even if your Bargman…
view full answer...It is possible to change your studs from 1/2" to 9/16" if you use drive-in studs and the the length and knurl diameter of the studs is the same, such as the 0.685" knurl diameter of the Kodiak Wheel Bolt - 9/16" #K916WB25. This…
view full answer...Yes you can wrap your the Blue Ox 7' Safety Cables - 7,500 lbs #BX88196 or 10,000 lbs #BX88197 around the trailer tongue, though ideally you would use a mounting bracket like the Brophy Safety Chain Mounting Bracket - 6-1/8" Long x 1/2"…
view full answer...To make sure the Ark Extreme Off-Road Swing-Up Trailer Jack #ORJW750BD will fit your trailer, there will be two things that need to be confirmed. First will be the tongue weight of the trailer you want to attach it to. This has a static, or resting,…
view full answer...Yes we do! The LED light that is comparable to the Bargman 40-06-001 and the Optronics #ST70RB that you referenced is the part #STL002RB with the staggered 3 pin connection. We also have the kit #TLL12RK which comes with the same size lights,…
view full answer...I do have options for you but there would be no way for me to know what type of light bulbs your trailer lights use. For trailer lights there are generally two types which are bayonet or push-in. Most taillights use a 1156 or 1157 bulb like part…
view full answer...Thanks for the pictures of your lights! Based on that you'd want the part #328-003-19R for red lights that match what you have and #328-003-19A for amber. These ground through a white wire but you can run that white wire's ring terminal to…
view full answer...Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…
view full answer...I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…
view full answer...Just click on the linked page to see all of our LED-type red oval trailer stop/turn/tail lights like #STL22RB from Optronics. This particular light measures 6-1/2- x 2-5/16-inches and uses a mounting grommet #A70GB and bracket #BK70BB. LED lighting…
view full answer...Yes, you just have to remove the old lights, match the wires and mount the new ones. Please note, that it is usually not a good idea to mix LEDs and incandescent lights, so if you have have side markers or other lights on the trailer, make sure you…
view full answer...The Buyers Products Hitch Plate with Receiver Tube - Ford #3371809061A is made specifically to fit the F-350, F-450, and F-550. It is built custom for what is termed as the 34 inch frame you are describing so it will fit your truck perfectly. The…
view full answer...