Customers compare MCL10RK1224B to these similar products
Products Featured in this Video
Jeff: Hello, everybody. This is Jeff @ etrailer.com. Today, we're going to take a look at this Uni-Lite round LED clearance and side marker light with the grommet and the red lens. Now, this is a nice small round LED trailer light that'll serve as a side marker and clearance light when it's properly mounted. It has a sonically sealed waterproof… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
We have a number of LED lights that fit a 1 inch diameter hole, for example the Peterson Piranha Mini LED Clearance or Side Marker Light w/ Grommet - 1 Diode - Round - Red Lens #M171R. This is a 3/4" light but comes with a grommet that measures…
view full answer...The Oval Reflector for Optronics Uni-Lite Trailer Lights, part #A11RXB may work well for your lights, even with a grommet like part #A11GB. I have attached a couple of photos that show the dimensions of both the #A11RXB as well as the #A11GB. The…
view full answer...The Peterson LED Mini Clearance and Side Marker Trailer Light w/ Grommet #M181R that you referenced only draws .04 of an amp. Which means all 20 of them would still only draw .8 of an amp. You could get away with pretty thin gauge wire but I'd…
view full answer...The difference is the grommet part #A11GB. The #MCL12RKB comes with it and the #MCL12RK does not. You should note that we do not carry the #MCL12RK.
view full answer...The LED Trailer Mini Clearance and Side Marker Light with Grommet - Submersible - 1 Diode - Amber Lens #MCL10AKB is the correct part you would need. This LED trailer light functions as both a clearance and side marker light when properly mounted. It…
view full answer...That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
view full answer...The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…
view full answer...In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
view full answer...If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…
view full answer...Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.
view full answer...Yes, 14 gauge wire seems too small. I would go with 10 or 12 gauge. For 10 gauge you can use #10-1-1 and for 12 gauge use #12-1-1. These wires are sold in increments of 1 foot. So if you needed 20 feet of wire you would enter 20 in the quantity box.…
view full answer...