5th Wheel Tailgate Options For 2010 GMC Sierra 1500 Pickup Truck

Question

Question:

Do you have any black aluminum 5th wheel tail gates for a 2010 GMC Sierra 1500 4x4?

asked by: Bill B

0

Expert Reply:

We have a couple of fifth-wheel tailgates for your 2010 GMC Sierra 1500. One we offer is part # VGM-07-100. It is made of steel, and not aluminum. I have included a link to an installation video for this tailgate on a Sierra you can check out.

The other is part # VGM-07-4000 which is made from a composite plastic material.

We do not carry an aluminum tailgate for your truck at this time.

expert reply by: Jeffrey L

0

Answer 1

That particular tailgate fits up to the 2007 model year. For your 2008 Silverado, you would need part # VGM-07-100. This tailgate will fit your Silverado if it is equipped with the steel bed, but not the composite bed.

view full answer...

Answer 2

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still close…

view full answer...

Answer 3

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 6

In order to charge your batteries wired in parallel with the NoCo Genius #329-GENIUS5 you'll want to connect the positive charge line to the positive terminal of the first battery and the negative line to the negative terminal of the opposite…

view full answer...

Answer 7

Yes, you can use the NOCO GEN On-Board Battery Charger #NOC34FR on your pickup's parallel batteries without disconnecting them. If your batteries were in a series, they would have to be disconnected. Since your batteries are parallel and maintain…

view full answer...

Answer 8

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 9

The DeeMaxx item #DE86VR won't because of the spacing on the mounting bracket but I have a caliper that will. To replace your Tie Down Engineering 46304 caliper you will need the Kodiak Disc Brake Caliper item #KDBC225DAC.

view full answer...

Answer 10

I recommend replacing an entire ladder if it's damaged. You'll want to find a replacement based on the height. Such as the Stromberg Carlson #LA-401 that is 99-1/2 inches tall. They can be cut shorter to customize the length if needed.

view full answer...

Answer 11

For a replacement you need the Titan Zinc-Plated Brake Actuator #T2477600. This is the Titan Model 10 which is the same as the Dexter DX12.5 you currently have on your boat trailer.

view full answer...

Answer 12

For your 2010 Forest River R-Pod 172 that has 3,500 lb Lippert torsion axles the correct lift kit is the #LC382741 that you referenced which will give you a 3-1/2 inch lift.

view full answer...