Would the Draw Tite Hitch # 75091 Have More Ground Clearance than Factory Hitch 2000 Toyota 4Runner

Question

Question:

I need a hitch that fits higher receiver than stock, My stock hitch drags fequently. Will this hitch fill that neec?

asked by: Dennis

0

Expert Reply:

After looking up some pictures of the factory hitches on the 2000 Toyota 4Runner it does appear as if they hang pretty low. The Draw-Tite Max-Frame Trailer Hitch # 75091 that you referenced should sit up a few inches higher than your factory hitch and should gain you some ground clearance.

I attached installation instructions for you to check out.

expert reply by: Jameson C

0

Answer 1

The larger spare should fit with the Curt item #C13087 but no one tests these hitches out for larger than stock spare tires. We just don't have that information available to us. The reason I say the Curt should work is the exact reason you…

view full answer...

Answer 2

When the manufacturer tests the fit of a hitch like the Draw-Tite #75091 they do not test for larger spare tires. From what I have found, the #75091 is about the same as the OEM hitch and leaves very little room for your typical spare tire. That…

view full answer...

Answer 3

The Draw Tite Hitch part #75091 is confirmed to fit your 2001 Toyota 4Runner and we had a customer write in a review saying that this hitch installs without any interference with the factory spare tire. The instructions for this product indicate that…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Since your 2024 Toyota Grand Highlander doesn't come with the factory tow package you need the Curt T-Connector Vehicle Wiring Harness #C79VV. The module plugs into that 10-Pin connector you found under the cup holder and then the 4-Way harness…

view full answer...