Can 2003 Mercedes-Benz M-Class Draw-Tite Frame Brackets Be Purchased Separately

Question

Question:

For item 75087 do you sell just the two frame brackets with hardware? Prior owner only installed the hitch, didnt bother with the brackets and no longer has them. Thanks!

asked by: Bryant C

1

Helpful Expert Reply:

If the brackets that come with the Draw-Tite Max-Frame Trailer Hitch Receiver # 75087 were listed under the hardware then we could sell you a hardware kit with part # RHK, but since these are considered part of the hitch itself those brackets won't be included in a hardware kit so you'll unfortunately need to purchase the whole hitch receiver kit to get those brackets.

expert reply by: Jon G

1

Frame Bracket for 2003 Mercedes-Benz M-Class Draw-Tite Hitch
(click to enlarge)

Answer 1

The Curt Trailer Hitch Receiver #13018 has the mounting bolt holes spread 3-1/4" horizontally by 2-1/4" vertically. These measurements are from center of hole to center of hole.

view full answer...

Answer 2

When installing the Curt #13018 on your 1999 Mercedes ML430, you will need to remove the bumper fascia. However, this actually isn't as difficult as it sounds as it is just a few bolts and it's off. I included an install video from a…

view full answer...

Answer 3

In the trailer world GTW stands for Gross Trailer Weight, and TW means tongue weight. Gross trailer weight is the entire weight of the trailer and tongue weight is the amount of vertical load that is on the coupler of the trailer. Basically how the…

view full answer...

Answer 4

If you take a close look at the Replacement Latching Spring Pin part #8880582 you will see that the cylindrical body has two notches on either side. If you take an opened ended wrench and place it over the body while aligning it with these notches…

view full answer...

Answer 5

It looks like you have the standard version, the Yakima HoldUp #Y02443. The replacement front arm #8880833 is only for the HoldUp EVO #Y02479 bike rack. You are correct that in your case, you will need to replace the entire front wheel assembly…

view full answer...

Answer 6

I went out to the warehouse to measure the Replacement Latching Spring Pin #8880582 and while I was able to confirm that it is essentially what you measured (between 23 and 24 mm), I wasn't able to get an exact measurement as the bag it is in is…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

Answer 11

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...