Mounting Hole Distances For Curt Trailer Hitch Receiver # 13018

Question

Question:

What are the distances between holes?

asked by: Brian

0

Expert Reply:

The Curt Trailer Hitch Receiver # 13018 has the mounting bolt holes spread 3-1/4" horizontally by 2-1/4" vertically. These measurements are from center of hole to center of hole.

expert reply by: Bud M

0

Mounting Hole Distances For Curt Trailer Hitch Receiver # 13018
(click to enlarge)

Answer 1

I went to the warehouse and pulled one of the Draw-Tite Max-Frame Trailer Hitch Receiver, part #75087. The plate thickness is 3/4-inch. The diameter of the mounting bolt hole is 5/8 inch. I have attached a couple photos of this hitch that shows the…

view full answer...

Answer 2

When installing the Curt #13018 on your 1999 Mercedes ML430, you will need to remove the bumper fascia. However, this actually isn't as difficult as it sounds as it is just a few bolts and it's off. I included an install video from…

view full answer...

Answer 3

If the brackets that come with the Draw-Tite Max-Frame Trailer Hitch Receiver #75087 were listed under the hardware then we could sell you a hardware kit with part #RHK, but since these are considered part of the hitch itself those brackets…

view full answer...

Answer 4

In the trailer world GTW stands for Gross Trailer Weight, and TW means tongue weight. Gross trailer weight is the entire weight of the trailer and tongue weight is the amount of vertical load that is on the coupler of the trailer. Basically how the…

view full answer...

Answer 5

I went out to the warehouse to measure the Replacement Latching Spring Pin #8880582 and while I was able to confirm that it is essentially what you measured (between 23 and 24 mm), I wasn't able to get an exact measurement as the bag it is in…

view full answer...

Answer 6

If you take a close look at the Replacement Latching Spring Pin part #8880582 you will see that the cylindrical body has two notches on either side. If you take an opened ended wrench and place it over the body while aligning it with these notches…

view full answer...

Answer 7

It looks like you have the standard version, the Yakima HoldUp #Y02443. The replacement front arm #8880833 is only for the HoldUp EVO #Y02479 bike rack. You are correct that in your case, you will need to replace the entire front wheel assembly…

view full answer...

Answer 8

Unfortunately there is not any adapter we carry for the 7-way US to the 7 pin European. The closest thing we offer is the US 4-way to European 7-way Round #118710. To use all the US 7-way trailer functions you would need to use a European 13-way…

view full answer...

Answer 9

U.S. 7 pins such as Pollak #PK11700 have different functionality than European style 7 pins, as the Euro style is essentially equivalent to our 4 way. What you are going to need to do is match up the wiring from both connectors; I've added a…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Mounting Hole Distances For Curt Trailer Hitch Receiver # 13018

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching