What All Is Needed To Install The Curt 13018 Hitch On A 1999 Mercedes-Benz ML430
Question:
I have a 1999 merz ml430.To install, does entire bumper need to be removed or just center access door? Also how far beyond bumper does receiver extend? Thanks
asked by: Steve D
Helpful Expert Reply:
When installing the Curt # 13018 on your 1999 Mercedes ML430, you will need to remove the bumper fascia. However, this actually isn't as difficult as it sounds as it is just a few bolts and it's off. I included an install video from a different hitch that shows how quick and easy it is to remove as well.
As to how far it will stick out from the bumper, I cannot say, unfortunately. We haven't had the chance to install one of these yet so I do not have this measurement, but I do have something that will help. I included a full diagram of the # 13018 that shows it to be 6 inches from where it will sit against the frame of your vehicle to the absolute end of the receiver. If you were to pop the center door out and use a measuring tape or ruler, you will be able to see exactly where the end of the hitch will sit.
(click to enlarge)
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- No Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Yakima HoldUp Bike Rack for 4 Bikes - 2" Hitches - Wheel Mount
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: Mounting Hole Distances For Curt Trailer Hitch Receiver # 13018
- Search Results: trailer hitch
- Search Results: yakima
- Article: Determining Trailer Tongue Weight
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Replacement Latching Spring Pin for Yakima HoldUp, TwoTimer, or FourTimer Bike Racks
- Video: Malone Anti-Rattle HitchLock System Review
- Video: Yakima HoldUp Bike Carrier End Cap Review
- Video: Yakima HoldUp Hitch Bike Racks Review - 2001 Chevrolet Tahoe
- Video: Malone Hitch Anti-Rattle - Standard Anti-Rattle - MPG908 Review
- Shop: Ultra Frame Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Shop: Thule Helium Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Wheel Mount
- Shop: Eye Bolts for Yakima HD Bar, JetStream, FlushBar, and RailBar Crossbars - 250 lbs - Qty 2
- Shop: B&W Pintle Hook Mounting Plate for 2-1/2" Hitches - 9" Shank - 8 Hole - 16,000 lbs
- Q&A: What do Trailer Acronyms GTW and TW Mean
- Video: Curt Cam Buckle Stabilizing Strap Review
- Video: Choosing the Right Trailer Wiring
- Search Results: hitch
- Q&A: How to Install the Replacement Latching Spring Pin Part # 8880582
- Q&A: What is the Thread Size for the Yakima Replacement Latching Spring Pin
- Q&A: Replacing a Broken Front Arm on Yakima HoldUp Bike Rack
- Video: Yakima Bike Racks Latching Spring Pin Review
- Q&A: What Size Are the Bolts Used to Mount the Curt 13018 Hitch
- Q&A: What Size Bolts Come with the Curt Trailer Hitch Receiver 13091
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Brake Controller
on Trailer Hitch
