Dimensions Of Mounting Bracket and 7-Way and 4-Way Trailer Connector # 30955

Question

Question:

Could you provide the bracket dimensions? Need to know the width.

asked by: Patrick J

0

Expert Reply:

The mounting bracket for the Replacement Custom Multi-Tow 7-Way and 4-Way Trailer Connectors # 30955 is 2-3/4" wide, 3-11/16" tall and 1-3/8" deep. The Connector itself is 3-1/8" wide and 3-1/16" tall.

expert reply by: Bud M

0

Connector # 30955 Dimensions
(click to enlarge)

Mounting Bracket For Connector # 30955 Dimensions
(click to enlarge)

Answer 1

To wire the 4 clearance lights #MCL0040ABB, license plate light #M298C, and tail lights #STL190RB to your 12' long 75" wide vintage trailer, I recommend starting the 4-Way Wishbone Trailer Wiring Harness with 42" Ground Wire #A40W42B…

view full answer...

Answer 2

I think you are going in the right direction. I would definitely replace the 14 gauge wire going to the trailer brake magnets with 10 gauge wire or larger. Usually larger than 10 gauge is hard to get into the trailer connector though. I would also…

view full answer...

Answer 3

Brakes can be installed on only one axle of a tandem axle trailer, however you should first check your state laws to see how many brakes are required for the gross vehicle weight rating (GVWR) of your tandem axle trailer. Some states require a…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 11

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 12

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...