Retractable Tonneau Cover Recommendation For a 2021 Chevrolet Silverado 3500 With Dually 8' Bed

Question

Question:

I want to install a retractable tonneau cover on my 2022 Silverado 3500 but it looks like they only fit the single wheel truck. Mine is a dually with the 8 foot bed. Do you have any covers that will fit my bed?

asked by: Kip

0

Expert Reply:

I recommend the Pace Edwards JackRabbit Retractable Hard Tonneau Cover # PE54UV for your 2022 Chevrolet Silverado 3500 Dually with the 8' Bed. This cover can be locked in 1' intervals allowing you to still protect your cargo and bed when you have to leave it partially open for large items. The matte black finish helps to give it a clean look that matches with the bed rail trim. The cover clamps in place so no drilling is required to fit this cover.

The Pace Edwards WeatherGate Tailgate Seal # 311-WG2001 will help to keep your bed free of dust, rain and snow from getting into the bed around the tailgate. Further protecting your in bed cargo with the tonneau cover.

expert reply by: Bud M

0

Answer 1

Yakima round bars like the round bars #Y00411 have a weight capacity of 165 lbs as a pair.

view full answer...

Answer 2

It sounds like you may be looking for the Replacement Rail Clamps for Pace Edwards Retractable Hard Tonneau Cover #PE54CV. This kit contains everything you need to replace your rail clamps on your Pace Edwards JackRabbit Tonneau Cover, however with…

view full answer...

Answer 3

If you had a hard freeze while the cover was wet and it's only had a little bit of time to unfreeze there could still be some ice build up that hasn't fully cleared to allow the locking mechanism to operate. If the truck wasn't sitting…

view full answer...

Answer 4

The replacement rail clamps #PE54CV for your Pace Edwards JackRabbit Retractable Hard Tonneau Cover #PE54UV on your 2010 Ford F-250, is not available separately from the kit. This kit does will work with the: -Bedlocker, -Bedlocker with Explorer…

view full answer...

Answer 5

Yes, you could cut down the Yakima Crossbars part #Y00411 and reinstall the endcaps.

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

Yes, you are correct. In order to correctly take this measurement you will need to measure from the center of the spindle to the center of the main axle tube. I have included a picture for reference.

view full answer...

Answer 8

In order to charge your batteries wired in parallel with the NoCo Genius #329-GENIUS5 you'll want to connect the positive charge line to the positive terminal of the first battery and the negative line to the negative terminal of the opposite…

view full answer...

Answer 9

Yes, you can use the NOCO GEN On-Board Battery Charger #NOC34FR on your pickup's parallel batteries without disconnecting them. If your batteries were in a series, they would have to be disconnected. Since your batteries are parallel and maintain…

view full answer...

Answer 10

The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to check…

view full answer...

Answer 11

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 12

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...