What is the Difference Between the Curt Hitch # C13417 and the Draw-Tite Hitch # DT73GR?

Question

Question:

what is the difference between the Curt Hitch C13417 and the draw-tite DT73GR on my 2021 Ford Ranger?

asked by: Anna

0

Expert Reply:

There are a few differences to consider between the Curt Hitch # C13417 and the Draw-Tite # DT73GR. First off, the Curt has a maximum tongue weight capacity of 900 pounds/maximum tow capacity of 6,000 pounds while the Draw-Tite has a maximum tongue weight capacity of 1,125 pounds/maximum tow capacity of 7,500 pounds. In addition, the Curt hitch is assembled in the U.S.A. while the Draw-Tite is manufactured and assembled overseas.

Also, when it comes to installation, the Draw-Tite requires you to lower your spare tire during the installation, where you can leave your spare tire attached during the Curt's installation.

Finally, there are differences in bumper clearance measurements and ground clearance. With the Curt, the distance between the center of the hitch's pinhole to the outside face of the rear bumper is about 4 inches and the ground clearance measurement is about 17 inches to the bottom of the hitch receiver to the ground. As far as the Draw-Tite, the bumper clearance measurement is about 5 inches and the ground clearance is about 17-1/2 inches. These dimensions are important for making decisions about what shank length/ground clearance requirements you need for your desired accessories.

With all things considered, I recommend the Curt hitch because it involves an easier installation and has the benefit of being assembled in the U.S.

If you are planning to tow on your 2021 Ford Ranger, I recommend the Curt Towing Starter Kit for 2" Hitches - 2" Ball - 3/4" Rise, 2" Drop # C45534. This kit comes with a compatible locking hitch pin.

If you have an idea about what accessories/cargo you wish to transport, feel free to respond to this answer with your needs and I will be happy to recommend the best products.

expert reply by: Bob C

0

Answer 1

Yes! Even though the Curt Trailer Hitch Receiver #C13417 which is confirmed to fit your 2021 Ford Ranger was installed on a blue truck, it will still work on your white truck. The color of your vehicle does not impact the fit & compatibility…

view full answer...

Answer 2

Good question, and thanks for the photo. I verified for you that the chain hooks on your 2022 Ford Ranger do NOT have to be removed in order to install the Curt hitch that fits, which is the following part number: - Curt Trailer Hitch Receiver…

view full answer...

Answer 3

Yes, there is a large difference in weight capacities between those hitch receivers for your 2021 Ford Ranger. I would be happy to break them down and compare them for you. The Curt Trailer Hitch Receiver item #C13417 is a custom fit for Ford…

view full answer...

Answer 4

There is not any added hardware required to install the Curt hitch that fits your 2022 Ford Ranger, which is the following part number: - Curt Trailer Hitch Receiver #C13417 Installation of the #C13417 on a '22 Ranger just requires removing…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...