Availability of Coupler Hinge Kit that Could Fit 2003 EZ Loader Trailer

Question

Question:

I have a 2003 EZ loader trailer, I would like to remove the tongue and add the swing tongue. Do you have the replacement for those? Thanks

asked by: Willis C

0

Expert Reply:

We do have coupler hinge kits available but what your 2003 EZ Loader trailer would need depends on the dimensions of your trailer's tongue. The part # FHDPB330301 is for 3 inch by 3 inch tongues, the part # FHDPB350101 is for 3 inch by 5 inch tongues, and part # FHDPB340301 is for 3 inch by 4 inch. So you'd have to measure your tongue to see which option would work best for you.

expert reply by: Jameson C

0

Answer 1

Oddly enough I can't find a decent u-bolt that we carry that would work well for your application.

view full answer...

Answer 2

I have a solution for you but the part #CE10190GA-4 is not available in a half kit so what you would want is the part #CE10190GA with the swivel bracket part #CE10206G. We don't have the bolt and nut though so you would need to supply that…

view full answer...

Answer 3

Based on the picture you submitted it looks like your trailer was originally intended for a different boat and you'd need to made some modifications to it to get all of the bunks to fit the hull proplerly. The CE Smith Double U-Bolt Bolster and…

view full answer...

Answer 4

The Fulton Fold-Away Hinge Kit, item #FHDPB230101, is designed for bolt-on installation. If you need a weld on kit, you would use the Fulton Fold-Away Coupler Hinge Kit, Weld On, item #FHDPW230300, for your application. To install either of these…

view full answer...

Answer 5

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...