Can Bunk Adapter # CC-255 Carry Camco Tote-N-Stor

Question

Question:

Would you be able to use this with the Camco 21 gallon sewage tote, the tote is a little long but well within the weight?

asked by: David D

0

Expert Reply:

As long as you secured the Tote-N-Stor securely on the Bunk Adapter part # CC-255 yes you could do what you are looking to do. There's no reason it couldn't be stored on the bunk.

expert reply by: Jameson C

0

Answer 1

If you can't place any weight on the trailer in any way that limits a lot of the options. Basically you'd have to decide if you could fit in in the interior or use a bunk like part #CC-255 as a platform on the tongue of the trailer.…

view full answer...

Answer 2

I may have an option for you but It is not a good idea to cut the tongue of the camper and elongate it. It will affect the structural integrity and the tongue weight of the trailer especially if you add a generator to the tongue. It sounds like you…

view full answer...

Answer 3

It would probably be much easier to fill tanks with the Stromberg Carlson Trailer Tray Cargo Carrier #CC-255 if you had a soft cover on the tanks instead of a hard cover.

view full answer...

Answer 4

The Stromberg Bunk Adapter part #CC-255 is a great solution for what you are looking for. This attaches to the frame members of your camper and gives you a platform up above the propane tanks to carry a generator. I attached a picture of this…

view full answer...

Answer 5

The Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers - 300 lbs #CC-255 does have the angled front corners as you stated. The generator dimensions of 22.5 x 17.3 will have absolutely no issue with fit as the generator won't…

view full answer...

Answer 6

The BAK Revolver X4 Hard Tonneau Cover part #BAK79131 will sit about 1-1/2" to 1-3/4" below the bed rail. According to my research, the 2019 Chevrolet Silverado 1500 has bedsides which are 22" tall which means that you will…

view full answer...

Answer 7

If you check out the picture I attached you can see that when the Stromberg Carlson Bunk Adapter part #CC-255 is installed you still have really great access to the propane tanks of the RV.

view full answer...

Answer 8

I have a great solution for you that will not require adding a hitch to the trailer so you won't have to move the spare tire and mount. Take a look at the Stromberg-Carlson cargo carrier #CC-255. It mounts at the front of an A-frame trailer frame…

view full answer...

Answer 9

It will be a close fit but your 18" x 25" generator will fit on the tray of the Stromberg Carlson Trailer Tray Cargo Carrier #CC-255. If you look at the linked photo you can see that the very front of the tray measures 24-3/4" long,…

view full answer...

Answer 10

The Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers, #CC-255 has about a 29" clearance from the top of the trailer frame at its mount point to the cargo tray. A 30 lb. propane tank measures approximately 24" in height so…

view full answer...

Answer 11

The Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers part #CC-255 is not going to provide the best ground for your generator. However, we do not carry Champion Generators therefore I strongly urge you to call the manufacturer to see…

view full answer...

Answer 12

I do have a possible solution for you but unfortunately there aren't any battery boxes available that will hold two 12V batteries and fit within a 21" length and 8" width. The closest thing we have is the TorkLift PowerArmor Locking…

view full answer...