How to Carry a Generator on an A-Frame Travel Trailer

Question

Question:

I just purchased a Jayco 265RLSW 30foot travel trailer. I have a generator that weighs approx 100lb that I am considering mounting on the back of the trailer. Could remove the spare tire and mount, keep it in the bed of my truck, and mount a small platform on a receiver for the generator. Is this possible with something you sell?

asked by: Randy

0

Expert Reply:

I have a great solution for you that will not require adding a hitch to the trailer so you won't have to move the spare tire and mount. Take a look at the Stromberg-Carlson cargo carrier # CC-255. It mounts at the front of an A-frame trailer frame and has a 300 pound capacity.

It holds the generator up above any propane tanks, jack, or other items already present at the front of the trailer. This unit will also be more stable than a hitch and cargo carrier mounted at the back of a trailer.

expert reply by: Michael H

0

Answer 1

The total weight of the Stromberg Carlson Tray part #CC-255 is 65 lbs.

view full answer...

Answer 2

The Mount-n-Lock GennyGo Generator and Cargo Carrier for RV Bumpers #MNT54FR has a 200lb weight capacity so you shouldn't have an issue with the carrier holding your 96lb Champion generator. The only issue may with with the weight capacity of the…

view full answer...

Answer 3

Stromberg Carlson specifically designed the #CC-255 Trailer Tray for carrying compressors, generators, cooler or other fairly large items up above the propane tanks. If the proper precautions are taken, such as frequently checking the propane…

view full answer...

Answer 4

With the Stromberg Carlson Trailer Tray Cargo Carrier #CC-255 installed on your trailer you would still have enough room to turn on/off your propane tanks. You also would still be able to take the tanks off if you needed to as well. The tray will sit…

view full answer...

Answer 5

It will be a close fit but your 18" x 25" generator will fit on the tray of the Stromberg Carlson Trailer Tray Cargo Carrier #CC-255. If you look at the linked photo you can see that the very front of the tray measures 24-3/4" long,…

view full answer...

Answer 6

The Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers part #CC-255 is not going to provide the best ground for your generator. However, we do not carry Champion Generators therefore I strongly urge you to call the manufacturer to see…

view full answer...

Answer 7

The Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers, #CC-255 has about a 29" clearance from the top of the trailer frame at its mount point to the cargo tray. A 30 lb. propane tank measures approximately 24" in height so…

view full answer...

Answer 8

The Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers - 300 lbs #CC-255 does have the angled front corners as you stated. The generator dimensions of 22.5 x 17.3 will have absolutely no issue with fit as the generator won't extend…

view full answer...

Answer 9

The BAK Revolver X4 Hard Tonneau Cover part #BAK79131 will sit about 1-1/2" to 1-3/4" below the bed rail. According to my research, the 2019 Chevrolet Silverado 1500 has bedsides which are 22" tall which means that you will have around…

view full answer...

Answer 10

Functionally, using the Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers, #CC-255 to mount propane tanks is workable. Although I caution that you ensure the propane tanks are at least as secured as the OEM positioning to minimize any…

view full answer...

Answer 11

It would probably be much easier to fill tanks with the Stromberg Carlson Trailer Tray Cargo Carrier #CC-255 if you had a soft cover on the tanks instead of a hard cover.

view full answer...

Answer 12

I do have a possible solution for you but unfortunately there aren't any battery boxes available that will hold two 12V batteries and fit within a 21" length and 8" width. The closest thing we have is the TorkLift PowerArmor Locking…

view full answer...