Stromberg Carlson CC255 Tray Compatibility with 22.5 x 17.3 Inch Generator

Question

Question:

Can you tell me if the 3400 Champion Gen set will fit this tray. The generator is 22.5x17.3. Im asking because I see it is clip cornered. Thank you!

asked by: Bob T

0

Expert Reply:

The Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers - 300 lbs # CC-255 does have the angled front corners as you stated. The generator dimensions of 22.5 x 17.3 will have absolutely no issue with fit as the generator won't extend past the rectangle roughly 20 x 24-3/4 that would use the clipped corner area. I've attached a photo to assist.

expert reply by: Jason S

0

click to enlarge

Answer 1

The BAK Revolver X4 Hard Tonneau Cover part #BAK79131 will sit about 1-1/2" to 1-3/4" below the bed rail. According to my research, the 2019 Chevrolet Silverado 1500 has bedsides which are 22" tall which means that you will have around…

view full answer...

Answer 2

It will be a close fit but your 18" x 25" generator will fit on the tray of the Stromberg Carlson Trailer Tray Cargo Carrier #CC-255. If you look at the linked photo you can see that the very front of the tray measures 24-3/4" long,…

view full answer...

Answer 3

The Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers part #CC-255 is not going to provide the best ground for your generator. However, we do not carry Champion Generators therefore I strongly urge you to call the manufacturer to see…

view full answer...

Answer 4

I agree with you. Having the Honda generator mounted on the actual trailer would be better than a basket or other device. Using the Trailer Tray Cargo Carrier, #CC-255, is an excellent option. This carrier has a 300 pound weight capacity and the tray…

view full answer...

Answer 5

The Stromberg Bunk Adapter part #CC-255 is a great solution for what you are looking for. This attaches to the frame members of your camper and gives you a platform up above the propane tanks to carry a generator. I attached a picture of this…

view full answer...

Answer 6

With the Stromberg Carlson Trailer Tray Cargo Carrier #CC-255 installed on your trailer you would still have enough room to turn on/off your propane tanks. You also would still be able to take the tanks off if you needed to as well. The tray will sit…

view full answer...

Answer 7

I may have an option for you but It is not a good idea to cut the tongue of the camper and elongate it. It will affect the structural integrity and the tongue weight of the trailer especially if you add a generator to the tongue. It sounds like you…

view full answer...

Answer 8

As long as you secured the Tote-N-Stor securely on the Bunk Adapter part #CC-255 yes you could do what you are looking to do. There's no reason it couldn't be stored on the bunk.

view full answer...

Answer 9

I have a great solution for you that will not require adding a hitch to the trailer so you won't have to move the spare tire and mount. Take a look at the Stromberg-Carlson cargo carrier #CC-255. It mounts at the front of an A-frame trailer frame…

view full answer...

Answer 10

Functionally, using the Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers, #CC-255 to mount propane tanks is workable. Although I caution that you ensure the propane tanks are at least as secured as the OEM positioning to minimize any…

view full answer...

Answer 11

If you check out the picture I attached you can see that when the Stromberg Carlson Bunk Adapter part #CC-255 is installed you still have really great access to the propane tanks of the RV.

view full answer...

Answer 12

It would probably be much easier to fill tanks with the Stromberg Carlson Trailer Tray Cargo Carrier #CC-255 if you had a soft cover on the tanks instead of a hard cover.

view full answer...

Stromberg Carlson CC255 Tray Compatibility with 22.5 x 17.3 Inch Generator

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching