Single Step Replacement Recommendation For 2011 Jayco Pop Up

Question

Question:

need to replace a single step on 2011 jayco pop up camper. existing mounting holes in metal frame under camper 22 inches wide and bracket has slot widths of 6 to 10 inches on both sides. Bracket width is 25 inches

asked by: Richard R

0

Expert Reply:

The Flexco Manual Pull-Out Step for RVs - Single - 7" Drop/Rise - 24" Wide - 300lbs Item # SMFP-1100 is the only single step we carry with a bracket width of 25". You'll need to drill new bracket holes to bolt this step system into your camper. If you want a a two step system please let me know what your entry height is and I can recommend the correct step for your needs.

expert reply by: Kevin C

0

Answer 1

Actually the Torflex Lift Kit - Single Axle - 2-5/8" Lift #K71-723-01 will not fit your 1993 Jayco 1206 KB pop-up camper. This lift kit has a weight capacity of 2000 lbs., I checked online and found that your Jayco has a 2440 GVWR. The…

view full answer...

Answer 2

To go with a larger tire diameter will require additional clearance that judging by looking at your picture it doesn't seem you have. It looks like a really tight fit from your picture so it most likely wouldn't fit but the next…

view full answer...

Answer 3

We do not have the direct replacement for your 1998 Jayco Eagle SD trailer. The Replacement Lenses for Wesbar Wraparound Tail Lights - Left and Right Hand Sides #W003372-73 are the most common replacement lenses and I've attached a photo with the…

view full answer...

Answer 4

The mounting bracket portion of the Pull Out Steps part #SMFP-1100 that you referenced is 6 inches long with a distance of 4-1/2 inches between mounting holes. From outside to outside of each bracket it measures 25 inches. From bolt hole center to…

view full answer...

Answer 5

found an answer to your question, unfortunately there are no direct replacement for your 1998 Jayco Eagle. The lenses have been discontinued and are no longer available. However, we do carry new taillight assemblies that can replace the OEM lights on…

view full answer...

Answer 6

The 2-1/4" opening is the standard for the A-Frame jacks. Your particular opening may appear different due to rust buildup over the years. I see a lot of these trailers switch over to a bolt on side mount jack due to being easier to access and…

view full answer...

Answer 7

I think you are asking about a trailer jack for your Jayco popup. If so we have just what you need. For an a-frame camper I recommend a jack like part #TJA-5000S-B. This is a sidewind jack that has a 5,000-lb capacity and has a 15-5/8 inch lift. This…

view full answer...

Answer 8

Loadstar ST185/80D13 Bias Trailer Tire #AM3S331 is a bias ply construction whereas the 185/80R13 you have is a radial tire construction. The difference is how the plies run inside the tire. You would want to keep the construction type the same on the…

view full answer...

Answer 9

If by tail light cover you mean a replacement lens then we do have a wide selection of these so there is a chance we may have what you need but I don't have any sort of parts breakdown sheet for a 1999 Jayco Eagle Pop-Up Camper so in order to see…

view full answer...

Answer 10

To select new trailer tires/wheels for your Jayco pop-up camper you'll want to confirm the trailer's axle rating so you can select wheels and tires that have the necessary weight capacity. Usually there will be a sticker or plate on the axle…

view full answer...

Answer 11

I have good news, our trailer jack that has a 2 inch outer diameter part #DL74MR would fit and work well. While it has a 1,000 lb weight capacity that does not mean 1,000 lb total trailer weight capacity. That capacity is the tongue weight capacity…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...