Which TorkLift Camper Tie Downs for 2017 GMC Sierra 2500 Denali

Question

Question:

what jare the #s for camper jacks for my vehicle?

asked by: Mike

0

Expert Reply:

It sounds like you're looking for TorkLift camper tie downs for your 2017 GMC Sierra 2500 Denali with a short bed. If you've got a factory hitch and no step or running board that extends under the bed of the truck, then the correct TorkLift tie downs are parts # TLC2220 (front), and # TLC3215 (rear). If you also need new turnbuckles, you can use the TorkLift Locking FastGun Turnbuckles for Frame-Mounted Tie-Downs - Stainless Steel - Black # TLS9529-2-LK.

If you actually need to replace the electric jacks themselves, TorkLift does not make a system for this, but you can use the HappiJac Electric Truck Camper Jack System - 36-1/2" Lift - 11,200 lbs # LC736515-ELKIT. This is a heavy duty camper jack system with an 11,200-lbs capacity that will help you easily load and unload your camper from the truck bed.

I've linked some review and installation videos of these parts for you to check out. If you've actually got a running board or step that extends under the truck bed, or have an aftermarket TorkLift hitch, just let me know and I can help you find the correct tie downs for that setup.

expert reply by: Erik B

0

Answer 1

The Brophy Clamp On Camper Tie-Downs part #HSBP will fit your 2015 Chevrolet Silverado 3500. However, we have not yet tested them on this truck while using a Sun Lite Truck Camper so I would not be able to confirm fitment though I do not see any…

view full answer...

Answer 2

The Brophy Clamp On Camper Tie-Downs #HSBP are not a fitguided item that list specific vehicles that it fits. It is more of a universal item. That being said, the Brophy Clamp On Camper Tie-Downs #HSBP will fit most full-size, non-dually pickup…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 9

There is no weight capacity for the Brophy Clamp On Camper Tie-Downs #HSSF. The tie-down hardware kit #TDHP, that is used to secure the camper to the #HSSF tie-downs has a weight capacity of 3,000-lbs. My contact at Brophy said the tie-downs will…

view full answer...

Answer 10

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

I'm happy to confirm that yes, the B&W Patriot 5th Wheel Trailer Hitch w/ Slider #BWRVK3270 with the B&W Universal Base Rails and Installation Kit for 5th Wheel Trailer Hitches #BWRVR3200, and the Draw-Tite 5th Wheel/Gooseneck Wiring…

view full answer...