Hanger Spacing When Using Leaf Springs SP-212275 with Hanger Kit APS4

Question

Question:

When using APS4 Hanger kit for the referenced springs, what is the correct spacing?

asked by: Tom

0

Expert Reply:

When using the hanger kit part # APS4 with the leaf spring part # e54SR the distance between the hangers will be 24-7/8 inches.

expert reply by: Jameson C

0

Answer 1

If your current springs are like the #e34SR which is 25-1/4 inches from eye to eye the correct measurement to use for the hanger spacing is 24-7/8 inches. At one point 25-3/4 inches was recommended, but we found that 24-7/8 inches was a much better…

view full answer...

Answer 2

When installing the 4-Leaf Double-Eye Spring for 4,000-lb Trailer Axles #e48SR I recommend using one of the kits below depending on the amount of axles you have and the length of the current straps. While the length does not have to match exactly you…

view full answer...

Answer 3

You will want to weld the hangers of the Single-Axle Trailer Hanger Kit #APS1. The holes you see are not designed to have bolts run through them. If you did run bolts they would most likely interfere with the spring and how it would sit on the…

view full answer...

Answer 4

Yes, you can flip the 4-Leaf Double-Eye Spring for 4,000-lb Trailer Axles #e22YR so they are on top of your axle. You'll need an over/under conversion kit, though the nut on the bottom won't fit in the hole of your axle, it'll fit in the…

view full answer...

Answer 5

The APS1, APS2, and APS3 are all suspension kits for single-axle trailers with 1-3/4-inch double-eye springs. They are designed for use on trailers with single, 2,000-lb to 7,000-lb axles. The difference in the kits are in the rear hangers and the…

view full answer...

Answer 6

The bushing on the Rear Single Axle Trailer Suspension Hanger is welded in place, and is not available separately. I walked out to our warehouse and pulled one of the hangers off the shelf. The outer diameter of the bushing is .76 of an inch as…

view full answer...

Answer 7

On the Redline Rear Hanger, part #30-20, which is the rear hanger included with kit #APS1, it is welded to the trailer with the side marked top, facing the outside of the trailer with the word top showing. So the U-shape part is what gets welded to…

view full answer...

Answer 8

Smart idea to get ahead of the problem, and there is a good upgrade for your Tracker boat trailer with a 3,500 lb axle. Since your current spring measures 26-1/4 inches from center of one spring eye to the center of your other spring eye, a 26 inch…

view full answer...

Answer 9

The Kodiak Disc Brake Kit, part #K2HR712, that you referenced will fit axles that are rated for 7,000 lbs that use a #42 spindle. It will work with 16 inch and larger wheels that use an 8 on 6-1/2 bolt pattern. Since axles can vary depending on the…

view full answer...

Answer 10

The number 8752 that you referenced doesn't match up with any seal numbers that we carry, but there is a way to determine what replacement seal you would need. You will want to measure where the seal rides on your axle spindle with a dial or…

view full answer...

Answer 11

I can help you find the correct bearings and seals for your 2007 EZ Loader boat trailer. It will require you to remove your bearings and seals. Your trailer's bearings and seals have part numbers on them. Once you remove the old bearings and…

view full answer...

Answer 12

The thickness of the grease seal like the #168233 won't matter. You're really just worried about the inner and outer diameter of the seal, so as long as your seal cross references to the National Seal 473317 this will be the correct…

view full answer...

Hanger Spacing When Using Leaf Springs SP-212275 with Hanger Kit APS4

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching