Recommended Draw Bar for Curt Class I Hitch on a 2019 Mitsubishi Mirage G4

Question

Question:

i need a draw bar four this whut would u say

asked by: Keith Y

0

Expert Reply:

The draw bar that is recommended to be used with the Curt Trailer Hitch Receiver # C11449 on your 2019 Mitsubishi Mirage G4 is the Curt # C45521 which has a 2-5/8" Rise/3-1/4" Drop.

To secure this to the hitch receiver you need a pin & clip # F-4 or locking hitch pin # C23517 and then you also need a hitch ball like the 1-7/8" # A-80 or 2" A-82.

A complete towing setup also requires wiring to activate the trailers lights. For your application I recommend the Tekonsha ZCI # 119250KIT because it clamps onto your OEM wiring instead of splicing and then it pulls power directly from your vehicle battery and includes a circuit-protected module so you don't have to worry about anything happening to your OEM wiring even if something malfunctions on your trailer side of things.

You can either leave the 4-Way in your rear hatch area or you can keep it next to your hitch receiver using the brackets # 18144 and # 18140.

Attached are some videos for you to check out.

expert reply by: Jon G

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

Yes, your kick sensor for your hands free liftgate will still work after installing a Class III receiver on your 2024 Toyota RAV4 XSE. I have linked an install video near the bottom of the page for our etrailer Trailer Hitch Receiver #e23ZR being…

view full answer...