What Size Bolts Come with Yakima Replacement Mounting Hardware # 8830021

Question

Question:

Hi, what is the diameter and length of the screw for this part ?

asked by: Jim D

0

Expert Reply:

I checked with Yakima and the bolt size that comes with the replacement mounting hardware part # 8830021 is 1/4-20 x 2.25" in size.

expert reply by: Jameson C

0

Answer 1

The Replacement Hardware Bag for Yakima Mako Saddles, LandShark Saddles, HullRaiser or Kayak Stacker #Y8840018 does look similar to the parts you are needing for your Yakima ButtonDown ski and snowboard carrier. But, it is not the correct kit that…

view full answer...

Answer 2

It depends on your bike mount and brand. Yakima has their Universal Mighty Mounts #Y03590 that should help with most of your Yakima carriers. Thule has their Xadapt series: #Xadapt1 and #Xadapt2 for crossbars that have a t-track in them. If not,…

view full answer...

Answer 3

We do indeed sell the replacement knobs you're looking for. They're available in a quantity of 4 as part #Y8860080. I know, you only needed one, but this way you'll have a few spares!

view full answer...

Answer 4

According to Yakima, the Load Ranger 16 is obsolete and unfortunately they no longer offer replacement parts. It's possible that the #8880683 you'd looked at could be made to work, but Yakima didn't have any advice to offer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof…

view full answer...

Answer 11

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 12

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

What Size Bolts Come with Yakima Replacement Mounting Hardware # 8830021

Product Page this Question was Asked From

Continue Researching