How To Determine if Replacement Front Foot Pad Fits 5th Wheel Trailer

Question

Question:

Will this fit a 2015 eclipse attitude 5th wheel toyhauler. This there a video of how these mount up. From looking at the picture aren’t clear to me.

asked by: Tim

0

Expert Reply:

As long as your 2015 Eclipse Attitude has a Lippert Ground Control 3.0 installed on it (4 point or 6 point) like the # LC675817 the replacement foot pad part # LC362486 does fit and work well for the front leg.

We don't have an install video that shows how this pad installs on the foot of a jack either. Basically all you do is line the hole up on the foot of the jack and then insert the snapper pin and clip it onto the other side of the pin and you're set.

expert reply by: Jameson C

0

Answer 1

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 2

Replacement Front Foot Pad for Lippert Components Ground Control 3.0 Leveling System #LC362486 does indeed have a 9 inch diameter. I have linked a video review of it for you.

view full answer...

Answer 3

Judging by the condition of your landing gear a new motor isn't all that you'll need. Plus the motor kit you mentioned is for stabilizer jacks which are a totally different style of jack. Your best solution will be a new Ultra Fab power…

view full answer...

Answer 4

The Replacement Front Foot Pad for Lippert Components Ground Control part #LC362486 is made specifically for the Lippert Components Ground Control 3.0 Leveling System which it does not sound like you have based on you saying you have rectangular foot…

view full answer...

Answer 5

The Atwood Premier Performance Series Power Jack when compared to the Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 23" Lift - 5,000 lbs - Black #JET-5000 will be slightly slower. The Atwood is a faster jack, but you do miss out…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...