Out of Stroke Error on Lippert Ground Control

Question

Question:

I am getting a out of stroke code in the Kwikee jack system will not do anything except come on

asked by: Mike H

0

Expert Reply:

I am a bit confused by your question as Kwikee does not make trailer jacks but rather trailer steps. If you were instead referring to trailer jacks such as the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part # LC358590 then the "out of stroke" error means you have extended the jack too far. If the jack will not retract using the touchpad then you will need to do so manually with the manual override on top or bottom (see photo).

If you continue to get an "out of stroke" error or you cannot manually retract the jack then that would point to signs of damaged internals which means the jack leg would need to be replaced. I have attached a list of replacement jacks below.

Front Leg - part # LC305340

Right Rear Leg - part # LC344792

Left Rear Leg - part # LC305339

If you need more height for your jacks then you can use the Ultra-Fab Leveling Blocks for Trailers and RVs part # UF48-979051.

expert reply by: Conner L

0

click to enlarge

Answer 1

In order to reset the control panel you will need to manually level the coach and then reset the zero point. If you need help with resetting the zero point you can follow the instructions below. If you were to unplug the control panel or control…

view full answer...

Answer 2

Yes, we do have replacement parts available. If I am following you correctly, you are looking for the replacement lead leg for your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System, #LC675817. This will be part number, #LC305340.

view full answer...

Answer 3

There are a couple of things as I talked with my contact at Lippert. You will need to follow this system perfectly of the error will not clear. You need to extend the front jacks 6 inches, then the rear jacks 6 inches, and then press and hold the…

view full answer...

Answer 4

I went out into our warehouse to pull a Lead Jack Repair Kit #LG-146059 to measure the length of the shaft and found it to be 6-1/2 inches.

view full answer...

Answer 5

To help I have included the written instructions below and also a diagram that points out the parts mentioned in the written instructions for the entire kit for the replacement gear and shaft kit for your Venture landing gear leg. The instructions…

view full answer...

Answer 6

I linked the schematic diagram for Lead Jack Repair Kit #LG-146059 taken from the written instructions. The complete instructions will be sent to you in a separate link. The follow leg repair kit is part #LC146060 in case you need it.

view full answer...

Answer 7

You should need repair kit #LG-146059 for the lead leg and #LG-146060 for the follower leg. From the picture you sent in I was able to determine that you have a Venture landing gear set VMC900R.

view full answer...

Answer 8

Based on my research your Keystone Raptor Velocity is equipped with Venture Landing Gear. The part number M-900-PK that you found on the lead leg indicates that the correct replacement Follow Leg should be the part #LG-177201. For just the repair kit…

view full answer...

Answer 9

The Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs #RVLG-8HDL will simply mount to the weld-on brackets by being bolted on. While an online copy of the manual is not available for this specific landing gear, I did cut out a portion of the…

view full answer...

Answer 10

The installation of the Landing Gear Set part #RVLG-8000 will be fairly straight forward. Basically, you will need to have a metal support structure so you can attach welded tabs part #LC113511 to it, 15-1/2" apart. Once these are installed you…

view full answer...

Answer 11

The thicker washer of the repair kit part #LG-146059 that you referenced is the thrust washer and the thinner one is the shim washer. I attached a diagram that shows how all of the pieces go together.

view full answer...

Answer 12

As long as your existing landing gear have their weld stops in the standard positions as shown in the linked photo (15-1/2 inside to inside and 17-1/2 outside to outside) and the outer tube length matches then the Ultra-Fab 12K dual motor landing…

view full answer...