Landing Gear Repair Kit Recommendation for Venture VMC900R Landing Gear

Question

Question:

My 5th wheel is a 2006 Everest 294L by Keystone . I have read your coverage of Venture landing gear but the part numbers you give are different than the number in the leg-cap of my Venture Landing gear. My number is VMC900R-149976. I need a lead-leg kit to replace the out-put shaft that twisted off. I am hoping you can give me the part number I need to replace this part.

asked by: Tim S

1

Helpful Expert Reply:

You should need repair kit # LG-146059 for the lead leg and # LG-146060 for the follower leg. From the picture you sent in I was able to determine that you have a Venture landing gear set VMC900R.

expert reply by: Jameson C

1

Answer 1

Yes, the Replacement Motor for Stromberg Carlson Electric Landing Gear #LG-142178 has been confirmed to replace the ADTH 1RV-200 landing gear motor you currently have so it would work for you.

view full answer...

Answer 2

Thanks for the pictures! Based on the part number of your motor it appears you have Venture landing gear. As such you will likely need follow leg rebuild kit #LC146060 or lead leg rebuild kit #LC146059 to fix your landing gear. Landing gear legs are…

view full answer...

Answer 3

Yes, I attached a diagram you can use to install the #LC146059 that you referenced.

view full answer...

Answer 4

Repair kit #LG-146059 contains 2 pins and the drive shaft all of which are for the top of the jack. To help I have included the written instructions below and also a diagram that points out the parts mentioned in the written instructions. The…

view full answer...

Answer 5

Landing gear is fairly universal in regards to the components like gears. I recommend the Follow Jack Repair Kit for Stromberg Carlson Landing Gear #LG-146060. This will work on many brands of landing gear. If you need to get specific, you can find…

view full answer...

Answer 6

The Lippert Components Venture Follow Leg Repair Kit for 5th Wheel RV Landing Gear #LC146060 is what you need for your follow leg. I've attached a photo to assist.

view full answer...

Answer 7

You might be able to get something like a center punch and tap it as much as possible at an angle. That could drive enough of it out the other side to be able to grab it with some pliers or vice grips. Another possible method would be to get a…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Landing Gear Repair Kit Recommendation for Venture VMC900R Landing Gear

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching