Trailer Hitch Recommendation for 2008 Subaru Impreza with Single Exhaust

Question

Question:

Hi, Im looking at EcoHitch Stealth Trailer Hitch Receiver - Custom Fit - 2inch Item # 306-X7261, and it says it fits 2008 subaru imprezas with quad exhausts. Im wondering if it fits a subaru impreza with a single exhaust? thanks

asked by: Kieran S

0

Expert Reply:

We have hitch fits for your 2008 Subaru Impreza with a single exhaust like the Draw Tite part # DT24959 which would fit and work well but the Ecohitch you mentioned states that it only fits models with quad exhaust.

expert reply by: Jameson C

0

Answer 1

It sounds like you have a Class I Trailer Hitch like the Draw-Tite #DT24959 installed on your 2017 Subaru Impreza. Certain Class I trailer hitches like this one feature a tab inside the receiver that prevents higher class accessories from fitting…

view full answer...

Answer 2

If you have a hitch-mounted bike rack like the Curt 2 Bike Rack for 1-1/4" and 2" Hitches #C18085 with a 2-inch sleeve, it will not make any noticeable difference as far as wobble if you get a hitch specially designed to only fit your 1-1/4…

view full answer...

Answer 3

I may have a solution for you, but you're not going to be able to open the rear hatch of your 2015 Subaru Crosstrek XV with the Thule Passage #TH910XT while bikes are attached since the added weight of the bikes would likely damage the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...