Mounting Location for 7-Way Connector on 2016 Hyundai Santa Fe SE with Curt Trailer Hitch

Question

Question:

Ill be installing the Curt Hitch #C13153 and the ETBC7 Kit on a 2016 Hyundai Santa Fe SE. I know that youve got the instructions down Ive done this before, but where are folks mounting the 7-pin receptacle on this vehicle? It was exposed on the 2009 model, but the bumper skirt covers most of the hitch.

asked by: Rod J

0

Expert Reply:

The Curt Trailer Hitch Receiver # C13153 referenced in your question, which is confirmed to fit your 2016 Hyundai Santa Fe SE, is indeed pretty hidden behind the rear fascia when installed on the vehicle. With that being said, there should be enough room directly to the left or right of the receiver to mount the 7-Way from # ETBC7 to the hitch cross tube.

The # ETBC7 Wiring Kit includes a mounting bracket for the connector and you can add the Tow Ready # 18140 or long # C57202 for a no-drill application, which will allow you to utilize a hose clamp to secure the bracket to the hitch. I have attached a short video demonstration on this product so you can see exactly how it works.

expert reply by: Chris R

0

Answer 1

The Curt Trailer Hitch, #12333, requires using the fishwire technique to get the bolts and block spacers into place. Removing them will be a little more difficult. You will have to push them up into the frame and try to guide them towards the…

view full answer...

Answer 2

As long as the controller is installed parallel to the direction of travel, and is level on a side-to-side plane, you can certainly mount the Tekonsha Prodigy P3 #90195 at a 45 degree angle to match the slope of your vehicle's dashboard. If…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 10

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...