USA Made Swivel Wheel Trailer Jack for Use in Saltwater

Question

Question:

Looking for a minimum 1000 lb swivel boat trailer jack that is fully galvanized and truly corrosion resistant for salt water service. Plated, coated, etc. is not what I am looking for. Not interested in a jack that fails after a couple years of use. Suggestions for a better grade jack? Made in USA a plus.

asked by: Dan

0

Expert Reply:

The Dutton-Lainson Swivel Marine Jacks are manufactured in the USA.

These include the # DL22580 and the # DL22800 1500 lb swivel jacks. These are both galvanized steel which will do a great job fighting saltwater corrosion.

expert reply by: Jameson C

0

Answer 1

If you need a replacement wheel for your Dutton Liaison Single Wheel Jack #DL22800, the part you need is #DL22410. The jack you have is not designed for a second wheel. Instead, I recommend the Fulton Bolt-Thru #FXPD15L. It features a two-wheel…

view full answer...

Answer 2

Scissor jacks are designed for stabilizing, not lifting. I wouldn't recommend you use one as an A-frame jack. You might be better off with a side mounted jack like the part #DL22800 that can be positioned further back on the trailer frame…

view full answer...

Answer 3

The swivel trailer jack we offer that has the lowest retracted height is the Fulton F2 part #F1413040134 which has a height of 11 inches from the center of its mounting bracket to bottom of wheel. The part #DL22800 has this height a little taller at…

view full answer...

Answer 4

I can certainly provide those measurements for you! I spoke with my contact at Dutton-Lainson about the Pull Pin, Easy Swivel Trailer Jack #DL22800 and Replacement Wheel #DL22410. He confirmed that the inner bore of the wheel measures 0.645 inches.…

view full answer...

Answer 5

The Dutton-Lainson Trailer Jack #DL22800 that you referenced will fit trailer frames that are up to 3 inch by 5 inch so it would work very well for you. The capacity for this jack is 1,500 lbs and can has 10 inches of lift. Check out the review video…

view full answer...

Answer 6

These trailer jacks come pre-greased and must be disassembled to be greased when needed. Dis-assembly starts with removal of the cap at the top of the jack. I have provided a drawing that should help with dis-assembly and re-assembly.

view full answer...

Answer 7

I have 2 trailer jack options that are bolt-on, side frame mount jacks that will offer you lower retracted heights than the 15 inch retracted height of your existing Dutton-Lainson jack. One is a similar Dutton-Lainson jack and the other is a Fulton…

view full answer...

Answer 8

We do have the replacement wheel you would need for your Dutton Lainson Jack part #DL22800. You would want the part #DL22410.

view full answer...

Answer 9

The reason why you do not see written instructions for repairs of jacks is the internal parts of a typical trailer jack are not end-user serviceable with the exception of the top gears. And with those it is just a matter of removing the old ones and…

view full answer...

Answer 10

Yes, the Pull Pin, Easy Swivel Trailer Jack #DL22800 will fit your Detail K2 Mighty Multi Utility Trailer #K2MMT4X6.

view full answer...

Answer 11

There are some Dutton-Lainson trailer jacks that are made in the USA as well as a few that are not. Any jacks that we carry that are made in the USA have that as part of the description to help set them apart. Currently we have the following options:…

view full answer...

Answer 12

Any of our parts that are manufactured in the USA have that noted in the item description. If you're looking for an American made product, the Dutton-Lainson Pull Pin, Easy Swivel Trailer Jack with 8" Wheel - Sidewind - 1,500 lbs #DL22800 is…

view full answer...