Trailer Jacks Manufactured in the USA

Question

Question:

I want a jack that in mfg. in the USA.

asked by: Don K

1

Helpful Expert Reply:

There are some Dutton-Lainson trailer jacks that are made in the USA as well as a few that are not. Any jacks that we carry that are made in the USA have that as part of the description to help set them apart. Currently we have the following options:
Pull Pin, Easy Swivel Trailer Jack with 8" Wheel - Sidewind - 1,500 lbs. # DL22800
Pull Pin, Easy Swivel Trailer Jack with 6" Wheel - Sidewind - 1,000 lbs. # DL22560
A-Frame Trailer Jack - Sidewind - 1,000 lbs. by Dutton-Lainson # DL22530
Pull Pin, Easy Swivel Trailer Jack with 6" Dual Wheels - Sidewind - 1,500 lbs. # DL22580
Pull Pin, Easy Swivel Trailer Jack with 6" Wheel - Sidewind - 1,000 lbs. # DL22457
A-Frame Trailer Jack - Topwind - 5,000 lbs. by Dutton-Lainson # DL22772
Pull Pin, Easy Swivel Trailer Jack with Foot - Sidewind - 15" Travel - 2,000 lbs. # DL22689
A-Frame Trailer Jack - Topwind - 2,000 lbs. # DL22781
Pull Pin, Easy Swivel Trailer Jack with Foot - Topwind - 10" Travel - 2,000 lbs. # DL22680
Pull Pin, Easy Swivel Trailer Jack with Foot - Sidewind - 10" Travel - 2,000 lbs # DL22686
Pipe Mount Swivel Style Trailer Jack with Foot - Topwind - 15" Travel - 2,000 lbs. # DL22682
Pipe Mount Swivel Style Trailer Jack with Foot - Sidewind - 10" Travel - 2,000 lbs. # DL22685
Pull Pin, Easy Swivel Trailer Jack with Foot - Topwind - 15" Travel - 2,000 lbs. # DL22683
Pipe Mount Swivel Style Trailer Jack with Foot - Sidewind - 15" Travel - 2,000 lbs. # DL22688

expert reply by: Jason S

1

William K.

9/7/2020

Ark swivel drop down stabilizer, how does it mount to trailer? I see 2 long bolts on its top not torqued down so assuming something to do with them.Video does not show how it mounts.

Reply

Jon G.

9/10/2020

Which Ark product are you referring to? None of them are listed on this answer page.

Reply

William K.

9/10/2020

@JonG Ark corner drop down RV corner stabilizer 2 1/2 foot AR94FR. Long corner steadies. I need to know how it mounts on a trailer so I can see if it will work for my high wheel camper trailer.tks

Reply

Jon G.

9/14/2020

@WilliamK Thanks for the part number! The Ark Drop Down Corner RV Stabilizer Jacks # AR94FR install by welding on that top saddle-looking bracket to your trailer frame.

Reply

See All (6) Replies to William K. ∨

Answer 1

The Buyers Products 15 Ton Pintle Hook with Mounting Kit #33710040 actually comes with the mounting hardware needed to get it installed but if you're needing to replace it you can find it with the Pintle/Combination Hitch Mounting Kit…

view full answer...

Answer 2

Good news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears #TJD-12000-RODNUT in the #12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience.…

view full answer...

Answer 3

I had the end loops of the Curt safety cables, part #C80176, measured for you. At their widest points the inside measurement is 3/4 of an inch and the outside is 1-1/2 inches.

view full answer...

Answer 4

The return springs in landing gear jacks are not replaceable or repairable unfortunately so if you have the #TJD-12000SP-R2NH.

view full answer...

Answer 5

The S-Hooks on the Curt Single Hook, Coiled Safety Cables with S-Hooks #C80176 you were looking at have an opening of 7/8" which is the largest S-Hook we offer, and should work great on the thicker safety chain connection point on your 2020 Ford…

view full answer...

Answer 6

I went out to the warehouse and pulled Dutton Lainson trailer jack #DL22800 to take the measurements for you. The 3 holes closest together are 1 inch apart on center. From the third hole to the furthest away hole is 2-1/2 inches. Side to side the…

view full answer...

Answer 7

Yes, you are correct. As long as your trailer frame is 3 inches wide across that top and 5 inches tall the Easy Swivel Trailer Jack, #DL22800, will fit on your trailer without drilling. I have posted a photo of a jack with the same mount installed on…

view full answer...

Answer 8

These trailer jacks come pre-greased and must be disassembled to be greased when needed. Dis-assembly starts with removal of the cap at the top of the jack. I have provided a drawing that should help with dis-assembly and re-assembly.

view full answer...

Answer 9

The buttons, face and controls on the Lippert Smart Jack Electric Trailer Jack w/ Footplate - A-Frame - 22-1/2" Lift - 3.5K - Black #LC643589 are not a replaceable part. You will have to use your warranty if you are within its time frame or…

view full answer...

Answer 10

The Lippert Smart Jack Electric Trailer Jack part #LC643589 is a good innovative option with memory features but it does have a design flaw in my opinion. The touchpad or controls are on the top of the jack. The reason that this is a problem is…

view full answer...

Answer 11

There was indeed a recall on the Lippert Smart Jack Electric Trailer Jack part #LC643589. It sounds like you have a pre-recall version but in order to confirm you can look on the back of the jack for a sticker on the stem with a serial number. If…

view full answer...

Answer 12

The Dutton Lainson jacks are all made in America. I attached a link to a page that has all of the Dutton Lainson trailer jacks we offer. A very popular option is the part #DL22300 which is made in America.

view full answer...

Trailer Jacks Manufactured in the USA

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching