Is it Possible to Add a Second Wheel to Dutton Liaison Single-Wheel Trailer Jack # DL22800?

Question

Question:

Would like to add another 8" x 2" wheel to my recently purchased Dutton Liaison Single wheel Jack purchase. I need and additional wheel and longer stainless steel axel bolt. 2" longer axel bolt x 1/2" diameter.

asked by: Steven M

1

Helpful Expert Reply:

If you need a replacement wheel for your Dutton Liaison Single Wheel Jack # DL22800, the part you need is # DL22410. The jack you have is not designed for a second wheel. Instead, I recommend the Fulton Bolt-Thru # FXPD15L. It features a two-wheel design, supports up to 1,500 lbs and can provide up to 12" of lift.

expert reply by: John R

1

Answer 1

If the copper wire has turned black, it will mean one of two things. First, salt water somehow got through the insulation/jacket, causing it to severely oxidize. Second, it overheated and actually burned some of that jacket. In either case, I highly…

view full answer...

Answer 2

The hole you have on your Dutton Lainson Jack part #DL22800 is not designed to be covered. If you really wanted to cover that hole you certainly could although you would be fine leaving it uncovered as well.

view full answer...

Answer 3

The wheel on the Dutton-Lainson Pull Pin Easy Swivel Trailer Jack is solid and made a poly molded hard plastic so you won't have to worry about a flat tire. The tire can also be replaced with Replacement Wheel #DL22410

view full answer...

Answer 4

Scissor jacks are designed for stabilizing, not lifting. I wouldn't recommend you use one as an A-frame jack. You might be better off with a side mounted jack like the part #DL22800 that can be positioned further back on the trailer frame for…

view full answer...

Answer 5

The reason why you do not see written instructions for repairs of jacks is the internal parts of a typical trailer jack are not end-user serviceable with the exception of the top gears. And with those it is just a matter of removing the old ones and…

view full answer...

Answer 6

The Dutton-Lainson Trailer Jack #DL22800 that you referenced will fit trailer frames that are up to 3 inch by 5 inch so it would work very well for you. The capacity for this jack is 1,500 lbs and can has 10 inches of lift. Check out the review video…

view full answer...

Answer 7

I went out into our warehouse and pulled a Dutton Lainson Jack #DL22800 to measure the distance from the bottom of the wheel to the center of the mounting bracket when retracted and found that distance to be 13 inches. Check out the video I attached…

view full answer...

Answer 8

At capacity your trailer will weigh 6,000 lbs plus the weight of your trailer. You will need to pick a jack that can safely handle the maximum tongue weight that your trailer will see. Tongue weight is usually 10-15 percent of the total weight of the…

view full answer...

Answer 9

I do carry replacement parts for the Dutton-Lainson Sidewind Swivel Trailer Jack, part #DL22800 that you have referenced. The replacement handle is the Dutton-Lainson Replacement Handle, part #DL22448 and the bushings for the handle you will need are…

view full answer...

Answer 10

Yes, the Pull Pin, Easy Swivel Trailer Jack #DL22800 will fit your Detail K2 Mighty Multi Utility Trailer #K2MMT4X6.

view full answer...

Answer 11

Usually, the jaw on the underside of a trailer coupler can be adjusted by tightening or loosening the nut on the underside of the jaw. If you loosen the jaw slightly, you should be able to get the coupler to come off the trailer ball. Once you get…

view full answer...

Answer 12

The bracket height on the Dutton Lainson Pull Pin, Easy Swivel Trailer Jack with 8" Wheel #DL22800 is 13", which is the distance from the center of the mounting bracket to the bottom of the wheel on this jack.

view full answer...