Dutton-Lainson Trailer Jack # DL22800 Recommendation for a 3 inch by 5 inch Frame

Question

Question:

my trailer has a 3 by 5 frame, will this fit? what is capacity?

asked by: Jae K

0

Expert Reply:

The Dutton-Lainson Trailer Jack # DL22800 that you referenced will fit trailer frames that are up to 3 inch by 5 inch so it would work very well for you. The capacity for this jack is 1,500 lbs and can has 10 inches of lift. Check out the review video I attached.

expert reply by: Jameson C

0

Answer 1

There are some Dutton-Lainson trailer jacks that are made in the USA as well as a few that are not. Any jacks that we carry that are made in the USA have that as part of the description to help set them apart. Currently we have the following options:…

view full answer...

Answer 2

The Dutton-Lainson Swivel Marine Jacks are manufactured in the USA. These include the #DL22580 and the #DL22800 1500 lb swivel jacks. These are both galvanized steel which will do a great job fighting saltwater corrosion.

view full answer...

Answer 3

The bracket height on the Dutton Lainson Pull Pin, Easy Swivel Trailer Jack with 8" Wheel #DL22800 is 13", which is the distance from the center of the mounting bracket to the bottom of the wheel on this jack.

view full answer...

Answer 4

I spoke to a technical contact at Midwest Industries and he advised that they use 800-lb-rated trailer jacks supplied by Dutton-Lainson. I contacted Dutton-Lainson and found the 800-lb jack referred to uses replacement pull pin kit #DL22449. This kit…

view full answer...

Answer 5

We do have the replacement wheel you would need for your Dutton Lainson Jack part #DL22800. You would want the part #DL22410.

view full answer...

Answer 6

The hole you have on your Dutton Lainson Jack part #DL22800 is not designed to be covered. If you really wanted to cover that hole you certainly could although you would be fine leaving it uncovered as well.

view full answer...

Answer 7

I went out to the warehouse and pulled Dutton Lainson trailer jack #DL22800 to take the measurements for you. The 3 holes closest together are 1 inch apart on center. From the third hole to the furthest away hole is 2-1/2 inches. Side to side the…

view full answer...

Answer 8

I can certainly provide those measurements for you! I spoke with my contact at Dutton-Lainson about the Pull Pin, Easy Swivel Trailer Jack #DL22800 and Replacement Wheel #DL22410. He confirmed that the inner bore of the wheel measures 0.645 inches.…

view full answer...

Answer 9

If the copper wire has turned black, it will mean one of two things. First, salt water somehow got through the insulation/jacket, causing it to severely oxidize. Second, it overheated and actually burned some of that jacket. In either case, I highly…

view full answer...

Answer 10

These trailer jacks come pre-greased and must be disassembled to be greased when needed. Dis-assembly starts with removal of the cap at the top of the jack. I have provided a drawing that should help with dis-assembly and re-assembly.

view full answer...

Answer 11

Scissor jacks are designed for stabilizing, not lifting. I wouldn't recommend you use one as an A-frame jack. You might be better off with a side mounted jack like the part #DL22800 that can be positioned further back on the trailer frame for…

view full answer...

Answer 12

Yes, the Pull Pin, Easy Swivel Trailer Jack #DL22800 will fit your Detail K2 Mighty Multi Utility Trailer #K2MMT4X6.

view full answer...

Dutton-Lainson Trailer Jack # DL22800 Recommendation for a 3 inch by 5 inch Frame

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching