Will Stromberg Carlson Replacement Follower Landing Gear Leg Fit a Venture Landing Gear System

Question

Question:

follow leg on 2012 big country 3250TS worm gear and nut are binding up only have about 8in of travel. Is the LG-177201 the right replacement leg ? Mine is a Venture and is 33 1/2 .

asked by: Hank J

1

Helpful Expert Reply:

Yes, you can use Replacement Follow Leg for Stromberg Carlson Landing Gear # LG-177201 with your Venture landing gear system. This same leg design is used by many manufacturers so it is interchangeable with them.

expert reply by: Michael H

1

Answer 1

Hey Ronald, the landing gear part #RVLG-8HDL does not come with new brackets but we have them available with the part #LG-Brackets. These will need to be welded on as there isn't a way to bolt on the jacks to the brackets you have now.

view full answer...

Answer 2

For starters, the Bulldog Powered-Drive Kit part #BD1824200100 for single speed or part #BD1824180100 for two speed is only designed to work with Bulldog landing gear legs that have a 12,000 lb support capacity. If you do not have these legs than I…

view full answer...

Answer 3

The only difference between a 4 leaf spring and a 5 leaf spring like the #e34SR is that the 4 leaf spring will use slightly thicker leaves and is 1/8 of an inch shorter. To get the best measurement of your existing springs, measure the center eye to…

view full answer...

Answer 4

I checked with Lippert Components and the Lippert Electric Landing Gear Set #LC333964 and the bolt that comes with the bracket needs to be torqued to 10-18 ft-lbs. You do need to be careful not to get it too tight because you could actually bend the…

view full answer...

Answer 5

Yes the etrailer Landing Gear Set - 36-1/2" Lift - 8,000 lbs part #RVLG-8000 can be used in the both the older exposed gear applications as well as the newer internal type of applications. I've included the video Jon did on the landing gear…

view full answer...

Answer 6

Trailer landing gear sets like the etrailer.com #RVLG-8HDL that you referenced are designed to bolt onto brackets that are welded to the frame. In terms of function or capacity there is no particular reason you couldn't just weld the legs…

view full answer...

Answer 7

Ram Landing Gear 12-Volt Motor Kit #LC142178 is rated for use with landing gear having up to an 8000-lb rating, such as set #RVLG-8000. Atwood's discontinued landing gear kit 75721 was rated for 5500-lbs so the new motor will have an easier time…

view full answer...

Answer 8

Landing gear legs do typically have weld stop brackets to hold the legs securely to the welded brackets on your trailer frame. The landing gear will have a maximum capacity lift, which for the Replacement Follow Leg for Stromberg Carlson Landing Gear…

view full answer...

Answer 9

The Lippert landing gear bracket #LC113511 is 2" long x 3-1/2" wide x 4-1/2" tall just like #LG-Brackets. The top portion of the bracket has a slightly different bend to it, but for all intents and purposes these are basically the same…

view full answer...

Answer 10

The only difference between the #RVLG-8HDL and the #RVLG-8000 is that the #RVLG-8HDL includes the manual crank handle, while the #RVLG-8000 doesn't. The dimensions for both are the same. • Retracted Height of 32-3/4 inches • Extended Height of…

view full answer...

Answer 11

I attached a dimension picture I got from Lippert for the Replacement I-Beam Jack Bracket #LC349975 that you referenced.

view full answer...

Answer 12

Your question came in totally blank, all I got were a couple pictures of a drop spindle axle on top of a leaf spring with the U-bolts removed. If you are having difficulty separating the leaf spring from the axle you might try some penetrating lube…

view full answer...

Will Stromberg Carlson Replacement Follower Landing Gear Leg Fit a Venture Landing Gear System

Product Page this Question was Asked From

Continue Researching