Dimensions of etrailer Brand RVLG-8HDL and RVLG-8000 Replacement 5th Wheel Landing Gear
Question:
I found you have had several people already contact you regarding replacing discontinued Atwood landing gear systems and have recommend either the RVLG-8HDL or RVLG-8000. While the spacing between the existing welded mounting tabs match what I have on my 5th wheel, on my my 5th wheel the bottom of the welded lower tab on the Atwood is 10inch to the inside bottom of the 5th wheel. Can you send me a complete dimensional diagram of the RVLG-8HDL and RVLG-8000 showing the total over all length of the unit 2.5inch tube along with the distance from the top to the upper welded tap and the distance from the bottom to the lower welded tab? I know that I will have to weld new brackets to make either of these work, I just need to figure out where I need to place the brackets so that the foot of the leg when fully retracted is below the bottom of the storage compartment.
asked by: Mike Y
Expert Reply:
The only difference between the # RVLG-8HDL and the # RVLG-8000 is that the # RVLG-8HDL includes the manual crank handle, while the # RVLG-8000 doesn't. The dimensions for both are the same.
• Retracted Height of 32-3/4 inches
• Extended Height of 53-1/4 inches
The tabs for the mounting straps measure 17-1/2 inches from the top of the top most tab to the underside of the lower tab. From the underside of the top tab to the top of the lower tab is 15-1/2 inches.
I've shown these dimensions on a photo for you.
Products Referenced in This Question
Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 7001 - 8000 lbs
- Landing Gear
- Sidewind Jack
- 36 Inch Lift
- Weld-On
- 2 Jacks
- etrailer
more information >
Product Page this Question was Asked From
Landing Gear Set - 36-1/2" Lift - 8,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 7001 - 8000 lbs
- Landing Gear
- Sidewind Jack
- 36 Inch Lift
- Weld-On
- 2 Jacks
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Bracket Dimensions of the etrailer RV Landing Gear System # RVLG-8HDL
- Q&A: 5th Wheel Landing Gear Motor Makes Loud Clicking Noise and Will Not Raise Trailer
- Q&A: Replacement Crank Handle for Ram 5th Wheel Landing Gear Compatibility With 2007 Fleetwood Nitrous TT
- Q&A: Troubleshooting Clicking Noise Coming From Landing Gear or Motor
- Q&A: How to Know if Landing Gear Set # RVLG-8HDL Will Fit 2001 Sunnybrook 31BWFS
- Q&A: Landing Gear Repair Kit for Venure VMC900L Follow Leg
- Q&A: Determining The Correct Replacement Landing Gear For A 2005 Thor Tahoe Transport 5th Wheel
- Article: Best Landing Gear
- Article: Trailer Wiring Diagrams
- Article: How Much Solar Power Do I Need For My RV?
- Article: Does Solar Panel Type Really Matter?
- Article: Most Popular Wheel Bearings
- Article: My Trailer Hitch Doesn't Fit
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box