Parts Needed to Flat Tow a 2016 Ford C-Max

Question

Question:

Have a 2016 Ford C Max and want to set it up for four wheels down towing behind MH. What braking system do you recommend?

asked by: Ted B

0

Expert Reply:

The easiest system to set up and use is the Blue Ox Patriot # BLU37TR, that applies the vehicle brakes in proportion to how much the tow vehicle is braking. This is the safest way to stop and it reduces wear and tear on both vehicles.

For a base plate kit I would recommend the part # 524432-1 which I attached an install video for as well.

The most popular compatible tow bar is the Falcon 2 # RM-520. For safety cables you can use # RM-643. The coiled design helps keep the cables off of the ground.

For lighting you can use the diode kit, # RM-15267, and not have to worry about cutting into the taillight housing. This will splice into your taillight wiring to allow your tow vehicle to control the taillight assemblies of the towed vehicle. This comes with a round 6-way connector that you will install on the front of your towed vehicle and enough coiled wire to go from there to the RV.

Most likely you will also need a high low adapter so that the tow bar will be level when you are flat towing. I attached a link to a page that has all of the ones we carry.

I have included a couple of helpful links to our articles on flat towing for you. Be sure to consult the vehicle owners manual for more specific information on flat towing your vehicle.

expert reply by: Jameson C

0

Dieter

1/30/2020

2016 c max hybrid TOAD any issues with cars braking system ? Thank you

Reply

Jason S.

1/31/2020

We haven't seen any issues with the 2006 Ford C-Max hybrid being towed. You simply need to make sure you have the 12V power outlet like # RM-9332 for portable braking systems like # BRK2016. For the stop light signal to be seen from your RV system, you will also need the Roadmaster Stop Light Switch Kit - Ford # RM-751459. I've attached a video to assist. Make sure to follow the towing setup in your owners manual to avoid any issues when towing.

Helpful Links

tv-install-roadmaster-stop-light-switch-kit-2014-ford-c-max-rm-751459.aspx

Reply

Answer 1

According to the owner's manual, the 2013 Ford C-Max is capable of being flat towed but you'll want to follow the procedures outlined in the owner's manual. For base plates, I'd recommend the #524432-1 from Roadmaster, for a tow bar,…

view full answer...

Answer 2

The difference between a tube extension and a hitch extension is splitting hairs on terms. The difference between a combo bar that you could drill a hole in and an extension is the finish. The extensions have a powder coated finish and the combo bars…

view full answer...

Answer 3

The longest adapter we carry is the Roadmaster High-Low Adapter - 2" Hitches - 10-1/4" Rise/Drop - 10K GTW, 400 lbs TW #RM-048-10. I don't know if you measured from the top of the receiver opening, but this will get you 10-1/4 inches of…

view full answer...

Answer 4

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 5

We offer ball mounts that fit 1-1/4 inch hitches that are compatible with 2 inch hitch balls. For example we have the #3593 which fits that hitch size and then for a 2 inch hitch ball we have the #19258.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Whether or not you can flat tow with a Jeep bumper is really up to the manufacturers testing; some of the big names like MetalCloak or Poison Spyder have bumpers with D-ring attachments that can be used for flat towing connections. This is great…

view full answer...

Answer 9

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Parts Needed to Flat Tow a 2016 Ford C-Max

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching