Ball Mount that Fits 1-1/4 inch Hitch with 2 inch Hitch Ball

Question

Question:

What part do I need to use a 2 inch ball on my 1 1/4 reciever? Without an adaptor

asked by: Ricardo

0

Expert Reply:

We offer ball mounts that fit 1-1/4 inch hitches that are compatible with 2 inch hitch balls. For example we have the # 3593 which fits that hitch size and then for a 2 inch hitch ball we have the # 19258.

expert reply by: Jameson C

0

Answer 1

According to the owner's manual, the 2013 Ford C-Max is capable of being flat towed but you'll want to follow the procedures outlined in the owner's manual. For base plates, I'd recommend the #524432-1 from Roadmaster,…

view full answer...

Answer 2

The Brophy part #HTAD is going to be the best solution we have. This is 7-1/4 inches long and is Class I hitch compatible. You should note that these adapters cut the capacity of the hitch they are installed in by 50 percent. I attached a review…

view full answer...

Answer 3

When you use a hitch adapter like the part #HTAD you cut the capacity of the hitch in half. The bike rack would not be affected, but the hitch and frame of the vehicle where the hitch attaches would potentially be affected if you were to overload…

view full answer...

Answer 4

We do have an adapter that will allow you to attach a 2" cargo carrier to the 1-1/4" hitch on your 2016 Nissan Altima. I recommend the adapter #e43YR. This is 6-1/2" long and will go in to your 1-1/4" hitch and…

view full answer...

Answer 5

The only trailer component that determines the speed rating of the trailer is the tires. All you have to do is simply replace your current tires with one that is rated for highway use, like the Kenda Loadstar #AM3S120 that you referenced, and you…

view full answer...

Answer 6

Consumers of aftermarket products are protected by the Federal Magnusson-Moss Warranty Act. The Act states that if something breaks on your vehicle and you take it in for warranty repair, the dealer must honor your warranty unless whatever…

view full answer...

Answer 7

Any type of hitch adapter or extender will have the unavoidable side-effect of causing a loss of about half of your hitch's rated capacity, both its tongue weight (TW) and it's gross towing weight (GTW). Hidden Hitch extender #HE18 and Curt…

view full answer...

Answer 8

The Rhino-Rack Aero Bars measure 3-1/8 inches wide. The Curt basket, #C18115, will fit bars up to 3 inches wide so it will not fit the Rhino-Rack bars. The Thule basket, #TH859XT, is designed to fit bars of many widths so it would be a great choice…

view full answer...

Answer 9

The Reese Cargo Carrier #63155 you referenced weighs 42 lbs; however, this carrier will only fit a 1-1/4 inch trailer hitch if it is a Class II hitch. This is important because the trailer hitches that fit your 2013 Honda Fit are either Class I…

view full answer...

Answer 10

On some models of the Matrix, the muffler heat shield is installed in such a way that it would be sandwiched in between the hitch and the underside of the vehicle. If this is the case, the heat shield would either need to be trimmed away or removed…

view full answer...

Answer 11

I do have an option that will allow for you to use your 2017 Subaru Outback to flat tow a 1972 Volkswagen Beetle, however, none of the 1-1/4" to 2" hitch adapters are rated for towing applications. Instead, you will need to use a 2"…

view full answer...

Answer 12

The longest adapter we carry is the Roadmaster High-Low Adapter - 2" Hitches - 10-1/4" Rise/Drop - 10K GTW, 400 lbs TW #RM-048-10. I don't know if you measured from the top of the receiver opening, but this will get you 10-1/4 inches of…

view full answer...

Ball Mount that Fits 1-1/4 inch Hitch with 2 inch Hitch Ball

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching