Recommended Weight Distribution System For 2004 Dodge Ram Towing Travel Trailer

Question

Question:

Hello, Im moving from a pop up to a very light 20 ft travel trailer. I need to know what hitch and sway control I would need, if any. The camper is 2840 lbs empty and 3500 lbs GVWR. Dry hitch weight is 370. Ill be towing with a 2004 Dodge Ram quad cab hemi, just under 8000 lbs towing capacity. Looking for fairly inexpensive, but easy to remove and would like to be able to go in reverse without removal. Was looking at part # FA94-00-0800. What would you recommend? Thanks!

asked by: Rick

0

Expert Reply:

The Fastway weight distribution system you were referencing, part # FA94-00-0800, requires a minimum 400-lbs tongue weight, and would not work for you but I do have a solution.

I recommend the Fastway e2 Weight Distribution System, part # FA92-00-0450. This system has a 4,500-lb towing capacity and a maximum 450-lb tongue weight capacity.

If you find you need a bigger system, I recommend part # FA94-00-0600. This system has a 6,000-lb towing weight capacity and can handle tongue weight between 400 and 600 lbs.

These systems allow backing up with the system installed, and are less-expensive than most of the systems available.

The hitch ball is not included with these systems. If you need a 2 inch hitch ball I recommend part # EQ91-00-6080, and if you need a 2-5/16 inch ball I recommend part # EQ91-00-6100.

expert reply by: Jeffrey L

0

Answer 1

For your 2012 Nissan Frontier and trailer hitch #87539 you will need a weight distribution system that is rated high enough for the total tongue weight of the trailer. This is calculated by taking the tongue weight of the trailer, when loaded and…

view full answer...

Answer 2

When it comes to weight distribution, tongue weight is the most important factor. In this case, it doesn't sound like the spring bars need to be swapped out. Although I don't know the exact model of your camper, the tongue weight is going to…

view full answer...

Answer 3

For your 2018 Nissan Pathfinder I recommend going with the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C13309 you mentioned as it has a hidden crosstube meaning the only visible part of the hitch is the actual receiver where the…

view full answer...

Answer 4

Choosing the right weight distribution system will depend on the total tongue weight of your setup. The total tongue weight will include both the loaded tongue weight of your camper plus any added cargo behind the rear axle of your tow vehicle. You…

view full answer...

Answer 5

For 411 lb of tongue weight the 6k rated Fastway e2 systems are the way to go. They have a tongue weight range of 250-600 lbs which your 411 lb tongue weight falls right in the middle of and that's exactly what you want. The trunnion systems like…

view full answer...

Answer 6

The Pro Series Weight Distribution System #49570 is likely too big a system for your trailer. If you want this style system, a better option for you is the similar system rated for 550 to 750 lbs total tongue weight #PS49582. Total tongue weight is…

view full answer...

Answer 7

The one important thing to consider when choosing a weight distribution system is actually the tongue weight of your loaded trailer. Typically, your tongue weight will fall between 10-15% of the total loaded weight of your trailer- a good tool to…

view full answer...

Answer 8

Yes, if you use a weight distribution system that is rated too high for the tongue weight of a trailer the ride quality will be incredibly stiff and harsh. You want to ideally pick a system that has a tongue weight range where your tongue weight…

view full answer...

Answer 9

Based on your explanation, I think the Fastway e2 Weight Distribution w/ 2-Point Sway Control #FA94-00-1000 will be large a system for your application giving you too stiff a ride. The light tongue weight of your trailer will obviously be slightly…

view full answer...

Answer 10

The ideal total tongue weight for a system rated from 400-800 lbs, in the case of the Fastway e2 Weight Distribution part #FA94-00-0800, is around 600-700 lbs. If your tongue weight is within that range, then this system will suit your needs just…

view full answer...

Answer 11

We have not had any issues with weight distribution systems bending trailer frames. If your trailer happens to have an aluminum frame that could be an issue though. You would need to check with the trailer manufacturer if the frame is aluminum to see…

view full answer...

Answer 12

The width of the Optronics Flexible LED Light Strip #UCL90CB is about 3/8". I have attached a review video where we take this measurement for you to check out. To help remove the 3M adhesive I recommend using some heat like a hair dryer or…

view full answer...