Does 2006 Toyota Tundra Factory Skid Plate have to be Removed to Install Front Mount Hitch # 31180

Question

Question:

Does the OEM skid plate on mt 2006 Tundra have to be removed to install this hitch?

asked by: Rob

0

Expert Reply:

I spoke with my contact at Curt about Front mount hitch # 31180 for the 2006 Toyota Tundra. He stated that the skid plate does not have to be removed, but there is some trimming of the plate that will need to be done in order to install the hitch. I have included a link to the installation instructions for this hitch below.

expert reply by: Michael H

0

Answer 1

We have had a few customers come back with similar Toyota Tundras as yours who said that with some minor trimming they were able to reuse the stock skid plate and have the Curt hitch #31180 installed. I attached a picture that shows the hitch…

view full answer...

Answer 2

The Draw-Tite front mount hitch #65031 requires removing the front skid plate for installation. See instructions and video links I have linked for this hitch. On front mount hitch #31180 you should not have to remove the skid plate. The 2001 model we…

view full answer...

Answer 3

According to the installation instructions, yes, the skid plate does need to be removed in order to install the Draw-Tite front hitch on your 2005 Toyota Tundra: - Draw-Tite Front Mount Trailer Hitch Receiver #65031 I did see the customer photo and…

view full answer...

Answer 4

For a front mount hitch for your 2004 Toyota Tundra, there are 2 options, see link. Both of them are going to require drilling, trimming, and/or removal of the skid plate for the hitches to fit properly. I would go with the Draw-Tite hitch, #65031…

view full answer...

Answer 5

For your 2018 Toyota Tundra the recommended front hitch is the part #31198 for use with the Agri-Cover SnowSport plow part A40000HD. You will need to enlarge a hole in the skid plate to allow the install of this hitch while also allowing easy access…

view full answer...

Answer 6

Unless you drive your Tundra pretty aggressively off-road, I would not be terribly concerned about removing that skid plate. I examined the instructions for the Curt Front Mounted Receiver, and the access hole the instructions refers to is not too…

view full answer...

Answer 7

When installing the CURT Front Mount Receiver, #31180, on a 2006 Toyota Tundra, you will need to drill a total of two 1/2 inch holes. I have included a link to the installation instructions for you. The other hitch we have for your truck, #65031,…

view full answer...

Answer 8

Both the Curt Front Mount Trailer Hitch #31180 and the Draw Tite Front Hitch #31180 that you referenced would be excellent choices for your 2002 Toyota Tundra. I would probably go with the Curt hitch only because it has been reviewed more times and…

view full answer...

Answer 9

I spoke with my contact at Curt and I have some measurements on hitch #31180 for you. For the mounting holes, they are 34-3/8 inches apart on center, side to side. The width between the mounting brackets is about 31-3/8 inches. I have included a…

view full answer...

Answer 10

I may have a different kind of solution for you, but based on the tongue weight of your trailer none of the front hitches we offer for your 2010 Toyota Tundra would work. The Trailer Valet XL part #TVXL25 is a great way to move trailer's around…

view full answer...

Answer 11

Apparently the skid plate on the 2007 Toyota Sequoia will interfere with the proper installation and placement of front mount trailer hitch #65031. You might be able to modify it and reinstall it but I cannot confirm that. The installation…

view full answer...

Answer 12

For the Draw-Tite front mount hitch, #65031, the skid plate will have to be permanently removed to install the hitch. You would also need to drill two holes in the frame rails (one on each side for the rear most hitch attachment points). I have…

view full answer...