Leaf Spring Hanger Options for 8x8 Tilt-Bed Trailer

Question

Question:

building a 8 x 8 tilt bed tailer for atv. 8 in tires 2000# axel and 2000# springs. wht hanger lenght do i use and is there a package axel set up ?

asked by: Ron

0

Expert Reply:

For the springs, I'd recommend the # e84SR spring, which is designed for 2K axles and measures 20-3/8 inches from eye center to eye center. If you need a U-bolt kit for this axle, # APUBR-10 will work well.

The hanger kit you use will depend on how much space you want between the axle and the trailer frame. Hanger kit # APS1 provides between 4-1/4 to 4-1/2 inches of clearance. # APS3 would give between 4 and 4-1/2 inches of clearance. # APS4 is 5 to 5-1/2 inches and # APS5 is between 4-3/4 and 5-3/8 inches.

We do stock a few off the shelf axles. If you would reply with your desired hub face to hub face dimension and the center to center measurement between the spring centers (which is about the center to center distance between the frame members, I'd be happy to make an axle recommendation for you.

expert reply by: Mike L

0

Answer 1

In the image with the suspension setup the equalizer #TREQ105 is placed between the front and second axles. Just like you have on your trailer. The front of the equalizer connects to the spring using a shackle strap and the rear is connected…

view full answer...

Answer 2

I have attached a drawing of a typical triple-axle setup you can check out. I have noted the locations you would install the #LC281288 kit shackles, bolts, sleeves, and nuts. As you can see, one of the equalizers does not use a replacement set of…

view full answer...

Answer 3

Thank you for all of that excellent information and photos! To replace the front equalizer you need the Curved Equalizer #TREQ104 and then for the rear equalizer you need the Equalizer for 1-3/4" Wide Double-Eye Springs #TREQ105. To replace…

view full answer...

Answer 4

When choosing between the Single-Axle Trailer Hanger Kit for Double-Eye Springs part #APS1, part #APS2, and part #APS3 it will be best to use the one that has measurements that most closely resemble what is already on your trailer. For example, if…

view full answer...

Answer 5

The APS1, APS2, and APS3 are all suspension kits for single-axle trailers with 1-3/4-inch double-eye springs. They are designed for use on trailers with single, 2,000-lb to 7,000-lb axles. The difference in the kits are in the rear hangers and the…

view full answer...

Answer 6

Usually air bags are used to help level out a load or offer extra support to the OEM suspension system, but it isn't unheard of to use them for smoothing out the ride from the OEM suspension while it's unloaded. I reached out to my contact at…

view full answer...

Answer 7

The highest capacity air helper spring kit offered for your 2012 and 2013 Ford F-550 Cab/Chassis trucks would be the Firestone Ride-Rite system, part #F2404 which provides 5600 lb of support. Neither Firestone nor Air Lift offer a higher rated…

view full answer...

Answer 8

I recommend using the Dexter Heavy Duty Suspension Upgrade Kit #K71-358-00 when you install the new Leaf Springs #e84SR. The upgrade includes 1/2" thick shackles with wet bolts and bronze bushings. These straps are much stronger than other…

view full answer...

Answer 9

The shortest shackle length is going to be 2-1/4" like the #LC122487. As for removing a leaf or two from your leaf spring, I would not recommend doing this. It will lower the weight capacity of your leaf spring and also require some…

view full answer...

Answer 10

I would be happy to help you find the correct replacement shackles for your 1997 Dutchmen 26FWRK-2 but you will need to measure your current shackles as I was unable to find any information on the specific ones used based on your VIN. To measure the…

view full answer...

Answer 11

The threaded portion of the bolts of the #K71-403-00 are 7/16 inch but the stepped up diameter is 9/16 inch. The shackle length is 3-1/8 inch from hole center to hole center. The bolt length is 2-7/8 inches. We can't help much with the axle…

view full answer...

Answer 12

Thank you for providing that information. In addition to the length you will also want to know the capacity of your axle so you can choose the correct leaf spring replacement. Assuming this is an older leaf spring, you will also need to account for…

view full answer...

Leaf Spring Hanger Options for 8x8 Tilt-Bed Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching