Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This heavy-duty, round jack is smaller than typical large-capacity jacks - perfect for tight-fitting applications. Has a 17-1/8" retracted height.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to take a look at the Bulldog round side wind jack without a mount and a 10 inch lift and a 2000 pound weight capacity. Now, this jack is a nice, durable, heavy gauge construction. The outer and the inner tubes overlap for nice additional strength when the jack's fully extended. They do use a weather-resistant coating on the outer tube and a zinc finish on the inner tube. It does offer a screw nut stop that'll prevent damage to the screw and/or the nut when this jack is fully extended.You notice it does have the side wind handle for a nice, smooth, ergonomic design for easy cranking. And also right up here by the handle, you can see they have a grease Zerk fitting that allow for easy lubrication of the bearings.
It does have long bearing and gear life. It does use an oil impregnated bushing. It is a direct well design. And this jack is ASABE compliant. Again, it is a round jack.Now, this does not come with a hole in the inner tube for mounting a foot plate.
Bracket height on this overall is going to be 17 and one-eighths inches when it's retracted. And when it's fully extended, it'll be 27 and one-eighths inches. So the travel is 10 inches. Lift capacity on this jack is 2000 pounds. Outside tube diameter is two and a quarter inches, and the inside tube diameter is two inches.As you can see, it has a nice ergonomic grip on the side wind handle.
Very easy to crank. To crank that way, you can see it extends out. And if you crank it this way, it'll rotate back.But that should do it for the review on the Bulldog round side wind jack without a mount, a 10 inch lift, and a 2000 pound weight capacity.
Average Customer Rating: 4.8 out of 5 stars (85 Customer Reviews)
This heavy-duty, round jack is smaller than typical large-capacity jacks - perfect for tight-fitting applications. Has a 17-1/8" retracted height.These are good jacks and work perfectly for our product. the only issue I have is that shipping is less than stellar. The jacks are packaged loose (I order 40 to 50 at a time if they have them available) and often arrive with the grease zerks broken off and paint scratched up. I have the means to repair the damage, it is just frustrating to have to repair something I order new.
Fast delivery! I have never been disappointed with any purchase from etrailer.
This is a great product and would be a 5 star if they did not get all scratched up in shipping
shipping was faster than Optimus Prime! Jacks arrived in good condition and well packaged. Best price I could find on the web. Thanks.
Excellent customer service & shipping s peed
Looks great.very easy purchase
Good quality jack that I installed on my trailer after the A frame jack was destroyed while towing my ATV during an elk hunt in the Gila. Excellent customer service and quick shipping.
Attached is a picture of how I am using the unit.
I have a two wheel trailer type sprayer manufactured by Rears Corp in Oregon. They supply a Bulldog 158151 with the sprayer to support the tongue when the sprayer is disconnected from the tractor three point hitch
To reconnect to the tractor it is easier to have a unit with a wheel which is why I ordered the BD1541150301 and BDCP555. It did take me over two months to get delivery, but the unit works fine.
You may want to contact Rears Corp and see if they would like to switch to the unit with the wheel. The only down side is that the 158151 supports 2000 lbs and the BDCP555 oly 1500 lbs.
Here are some pictures of what I used your product for. The splitter just had a fixed position stand and it is fairly heavy so it was difficult to hook to the ranger because the stand had to be removed first. Now I can just let it down to the hitch and with the wheel I can also move it around the shop without lifting it. We also put an extra mount on the back so the wood falling from the splitter would not damage it. Thanks for the good service,
Jack fit my receiver very well. The pin was a little big for my receiving mount but that can be remedied. The wheel has a loose fit to the hitch but works quite well.
Overall it’s a pretty decent fit and will surely help at the campsites. Thanks!!
I have used this product previously though it was supplied by a different vendor who had terrible reviews and is now out of business. I am a snowmobile nut and use this product to build snowmobile lifts for myself and friends. etrailer.com supplied this same jack for a better total price than I got 2 years ago from the other company and the etrailer folks were super to work with. One call and everything was set up and they kept me informed my order status all the way through til delivery. Great customer service and will do business with these guys in the future.
Can't go wrong with Bulldog - needed shorter tongue jack to enable parking on my slopped drive way - this was the charm.........
High quality lift - works well.
I used this jack for a very tiny teardrop I was building to pull behind my car. I chose it because this was the lowest stand I could find to crank down to the low hitch on the car. It's a great quality hitch and very versatile combined with the weld on pipe mount.
There are a few draw backs to consider but only for similar applications. It's a much heavier stand than I need for a lightweight trailer. To save weight I didn't add a foot but this allows the telescoping lift peice to spin in the outer housing rather than crank up until it contacts the ground. Not a big deal I just touch with my toe until it hits ground. Also w/o a foot it sinks in soft ground.
Summmery... Great quality. Great if you need to crank low and compact. A bit too heavy duty for a really lightweight trailer.
The product works perfectly with my teardrop trailer. It's adjustable in length so I can level my trailer when I park it. To remove the hitch from my car I can raise it up and let it slide off my vehicle. I have a wheel on the mount so I can just roll it away from my car. I am 100 lbs and can do this myself.
I installed the trailer jack as soon as I received it and it has been working great for a year. I installed it on a 3,000 gallon water trailer.
Bulldog Jack-BD1541150301 -Product received as expected
Weld on jack pipe mount-BD015279 -Product received as expected
6" heavy duty caster - BDCP555 -Very disappointed w/ product received. The "6 caster on your website is shown w/ pin to attach to jack. The caster I received did not have the pin shown.Very disappointed.
i have a side mount jack welded to my boat trailer . as i did not want to weld on the trailer , i got this jack that has more lift and capacity than my old jack , removed the swivel part off the trailer , cut out the old tube , and welded on the new jack tube , this also let me set the down position where i wanted id . jack is ridged and cranks smoothly
I bought this as a Christmas present for my husband. He is building a trailer for us to take on camping trips. He had mentioned that he was looking at this item for his project. I received it within a few days of placing the order (which is great since I am a notorious last minute shopper). Admittedly, I did not look at the item when it arrived, I just wrapped it up and put it under the tree. However, when my husband unwrapped it, even I was impressed. He's even more excited to get going on completing the trailer now. Perhaps I'll review again once it is complete... until then.. great job so far!
Just what I needed to replace an older 1000lbs Bulldog jack on my snowmobile lift. I can now use a drill to raise/lower the lift without using the crank handle.
Do you have a question about this Trailer Jack?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jenny N.
2/1/2022
I will have our customer service team reach out to you