T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
(76 reviews)
Price: $61.10
In Stock
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
Item # 118422
Retail:$80.86
Our Price: $61.10
You Save: 24%
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (76)
- Q & A (0)
- Photos
Tekonsha Custom Fit Vehicle Wiring - 118422
- Custom Fit
- Trailer Hitch Wiring
- 4 Flat
- Powered Converter
- Tekonsha
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring. Powered ModuLite reduces strain on wiring system.
Features:
- Provides a 4-way flat trailer connector at the back of your vehicle to power your trailer's signal lights
- Compatible with 5-pole, 6-pole and 7-pole adapters (sold separately)
- Connects quickly and easily
- Locate connection points in trunk
- Plug in T-connector
- Run hot lead to car battery
- Includes ModuLite power module that connects directly to battery to avoid overloading vehicle's electrical system
- Constructed of 16-gauge bonded wire
- Comes with dust cap for 4-way flat connector
Specs:
- Maximum amperage:
- Stop/turn lights: 2.1 amps per circuit
- Tail lights: 4.2 amps per circuit
- 1-Year limited warranty
Installation
This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located inside your trunk, behind the tail lights on both the driver's side and passenger's side. You will need to remove some interior trim or carpeting to access this harness. Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery and insert the provided fuse.
Once installation is complete, the 4-way flat connector will be stowed within your trunk.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
ModuLite Power Module
A ModuLite power module is built into this T-One connector. With a ModuLite, your trailer's lights will be powered without overloading your vehicle's electrical system. Because the module draws power directly from your car's battery and bypasses the electrical routes that are used by a basic wiring harness, there is virtually no draw on your tail light circuits.
118422 Tow Ready T-1 T-Connector - 4 Wire - Modu-Lite
Installation Details
This Product Fits The Following Vehicles
- 2011 - 2013 Ford Fiesta Sedan
- 2010 - 2012 Ford Fusion
- 2006 - 2012 Ford Fusion
California residents: click here
Customer Satisfaction Score:
93% were satisfied with this product
7% of customers were not satisfied
- Wrong item was ordered
- Manufacturer issue
- etrailer mistake
Customer Reviews
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector - 118422
Average Customer Rating: 4.9 out of 5 stars (76 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring. Powered ModuLite reduces strain on wiring system.by: Levi02/27/2024
Haven't tested if the harness works yet but there was more to it than advertised and their install video doesn't show the full install. I had to do some soldering but I got it all hooked up and my tail lights work good with it in there should be no problem with the trailer
by: Jeffrey 03/25/2024
It was very easy to order my wiring harness. It came a day earlier than expected. Very great place to purchase from.
by: Marc03/31/2013
2010 Ford Fusion
The wiring kit is solid! Super easy to install, especially with the awesome online video tutorial. The only thing I did different was that I ran the wire from the trunk through the inside of my Ford Fusion to the firewall where I went through an easy plastic port. I just couldn't see me running a wire underneath the car. I used this in conjunction with the Hidden Hitch trailer hitch and now i'm set up to haul my quad. Awesome price, fast shipping, great follow up. I'd recommend etrailer to anyone!!
by: Mark S07/04/2017
2012 Ford Fusion
I received all the parts promptly. Packaging was very sturdy and no shortages. I installed the hitch in 20 minutes! The wiring took a bit longer just because I had to work under the car, no lift in my driveway.
The install worked exactly as your video showed. Thank you to etrailer for the prompted service and very detailed video instructions. I will be back to etrailer for certain!
Mark S.
7/4/2018
The hitch has been in use for a year now and still no issues. I periodically check the wiring visually and with a meter. All works fine. Bolts are still tight.
by: Bill07/01/2014
Hitch and wiring harness was shipped out the same day I ordered it arrived in 2 days both the hitch and harness were easy to install and work great. Thanks etrailer
Bill
7/1/2015
Everything still works great
by: Mark02/19/2018
2010 Ford Fusion
This kit works excellent, used it with 18140 short bracket and 18144 four-pole mounting bracket. All in all, a professional looking install. Very happy
Mark
3/2/2019
this kit makes for a professional wiring install. Was able to run power wire completely through interior of vehicle, there is a plastic plug located in the firewall, above the gas pedal, which allowed access to the engine compartment for power hookup. Very nice.
by: Roy K05/15/2015
Every piece fit perfectly, easy install, the most difficult task was getting the muffler hangers off. Two sets of hands and a car hoist would have sped it up considerably but all in all not hard at all. The wiring harness was a snap. Again everything fit perfectly and was of good quality. I installed the hitch, did the wiring for the trailer, and assembled a Harbor Freight trailer in two days!!! Thanks for great products. Now I won't have to buy a pickup!
by: Loren Richardson08/11/2017
2008 Ford Fusion
Ordered the trailer wiring kit for a Ford Fusion. The T-one harness. As usual, fast delivery of product and it arrived with all the accessories as described. Good quality wiring and a nearly effortless installation. Worked first time I turned the lights on. Cudos again goes to etrailer for a great product at a great price and George J's immediate email to follow up on one of his products. Great customer service and it just goes to show that they care about their customers and want to see them succeed.
by: Chris V07/28/2016
Etrailer.com has gone above and beyond again with a great competitive price and Shipping my order very very promptly. Amazing company.
Oh yeah, I got just what the doctor ordered for my car so now off to the lake with my jet ski.
Chris V.
7/28/2017
Holding up very well, just went camping at Limerick Rock without a Hitch! Pun intended!
by: Wes Everett04/20/2015
2006 Ford Fusion
Easiest trailer wiring installation I've ever done. Installation video was right on and very helpful. Wire length was excellent. Everything fit like it should and quality of the kit is superb. Works like a champ! Delighted with the results.
by: Jim N.06/26/2012
2010 Honda Pilot
I ordered this harness when ordering a trailer hitch. As with the, shipping was fast. And like the hitch, I spent some time watching the installation video to prepare. This product installed pretty easily though I had to modify a couple of items from the video.
First thing I modified was running the black wire to the battery. The location of the access hole used in the video did not exist on my 2010 Fusion. Instead, I ran the wire along a wiring harness into the rear passenger compartment and out an access hole under the rear seat on the driver side. Then followed the brake lines into the engine compartment.
Second, after drilling the pilot hole for the included self tapping screw and screwing the ground to the body, the screw would not tighten down. Instead I found a slightly larger metal screw that worked just fine.
Overall, I would recommend this harness for it's relative ease of installation and quality.
by: Dave K07/17/2014
2012 Ford Fusion
The first trailer wiring I have installed that required a direct connection to battery. This was hardest part of the install, especially without a hoist. Also, had to watch the video for 2011 Fusion as the 2012 Fusion install video was not workable as far as an access to outside of car.
by: Tom R.09/25/2013
2012 Ford Fusion
This was the best response and service I have ever received on an on-line purchase. Order arrived faster than expected, everything was perfect. It only took me about 30 minutes to install the hitch, and another 30 for the wiring. I thought to myself while doing this, I should get in the trailer hitch business! This was easy. Thank you.
by: Arnie06/04/2017
I installed 2 of these years ago. I was a lot younger 88 now. I did do the wiring harness not so much weight there. I decided to let someone else do the hitch for me.
The instructions & videos are great !
There is my oil change man, I'll ask him. I owe him, he rotated my tires for free.
You fellows keep doing the excellent work you are doing now, wish I could say more. I would recommend you & your product to everyone.
by: Larry L.08/15/2015
2010 Ford Fusion
This is my third trailer hitch installation from etrailer, and I have to say that they have performed admirably in all three cases. The items ordered arrived in a timely fashion, and all orders were correct. The install how-to videos are a very nice service provided by etrailer. Overall I would highly recommend etrailer.
by: Steven04/22/2020
Shipping was fast, everything fit excellent,very well thought out. I’m extremely happy with this purchase ( trailer hitch and wiring harness) would definitely buy from etrailer. com again.
by: Bonnie06/25/2019
2007 Ford Fusion
Ordered both a hitch and wiring harness, to haul my kayak trailer. Perfect fit, and fairly easy to install the hitch. Even simpler to install the wiring. Love this site. I'll be back for any other items I may need. Thanks!!
by: Glenn03/09/2019
shortly after ordering my wire harness I developed health issues and it is still in the box laying on the new hitch in the garage I will update if and when I get them installed
by: Tom05/03/2015
2012 Ford Fusion
Ordered the hitch and wire harness and it was delivered in 3 business days. The order was complete and everything went together just like in the video. Will think of etrailer.com again and recommended it to my son.
by: Bonnie06/25/2019
2007 Ford Fusion
This is my second order from etrailer. LOVE this website!!! So easy to find what you want, and order. Very prompt delivery!
I look forward to installing my wiring harness, so I can haul my kayak trailer. Thanks for making it a breeze!
by: Jeffrey M.03/19/2013
2011 Ford Fusion
Great hitch!! Installed in no time. The wiring always takes longer, esp having to run a power wire on this model to the battery.
by: Dick T11/05/2013
2012 Ford Fusion
I have not mounted the trailer hitch to my car as of yet, but I have read the instructions, viewed the video on how to install everything. I believe it will take me about an hour to install everything.
by: Sean 06/03/2020
2009 Ford Fusion
Simple wiring and very straight forward installation video makes for an easy installation. Fits and programs perfectly for a 2009 Ford Fusion SEL with the 3.0
Only complaint is that I think there are to few zip ties as I needed to use my own.
by: Corey R04/10/2015
2012 Ford Fusion
Everything was perfect. you can hook it up to your lights in a few minutes. Watch the video provided on the website. The tougheset part was getting the power wire to the battery. I had no exit hole in the trunk so i punched one through and siliconed the hole.
by: Scott Evans04/12/2012
2011 Ford Fusion
The video was key to the install, easy as pie !
25
76
Show More Reviews
See what our Experts say about this Tekonsha Custom Fit Vehicle Wiring
- Installation of T-One Wiring Harness Splicing Into Aux 12V Connector at Center ConsoleThe T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118422 is recommended to be installed to draw power directly from the battery. Splicing into your 12V Aux will work as long as you have the fuse rating properly accounted for as you referenced and as long as you isolate the 12V Aux so when you use it to charge your phone, etc, doesn't steal power from the trailer connector. We don't recommend installing in this way. You need the 12V power to be correct so you don't...
view full answer... - Necessity of Routing Power Wire for T-One Wiring Harness # 118422 When Installed on 2010 Ford FusionAlthough the T-One Vehicle Wiring Harness you mention obtains its signals from plugging inline with the existing tail light wiring harnesses, the voltage to power the trailer lights needs to be drawn directly from the battery. The reason for this is twofold. First, the vehicle manufacturer has determined that any voltage drawn through the vehicle wiring over and above that needed to operate the vehicle tail light assemblies could overload the vehicle wiring system and damage it. Secondly,...
view full answer... - Will Trailer Wiring Harness # 118422 Fit a 2011 Ford Fusion HybridAccording to Tow Ready, the T-One Vehicle Wiring Harness with 4 Pole Trailer Connector, # 118422, will fit all style of the 2011 Ford Fusion, including the hybrid model. I have included a link to the installation details for you to view and a link to a video showing a typical installation.
view full answer... - Routing the Power Wire for a Trailer Wiring Harness for a 2014 Ford FusionYou seem to have found the silver lining in that your 2014 Ford Fusion is well built! Look for a factory harness that goes from the cab of the vehicle through the firewall. You may have to look in some tight places. If you cannot locate a harness, or it is not within easy reach or the wire just will not fit, you will have to drill a little hole and route the wire through it. Of course you will need to be careful where you drill so as not to damage anything on the opposite side of the...
view full answer... - Trailer Wiring and Hitch Recommendation for 2010 Ford FusionFor trailer wiring for your 2010 Ford Fusion the T-One kit part # 118422 would be the best option. This brand of trailer wiring is the most reliable that we offer so we recommend it highly. It would work great with the Draw Tite hitch part # 24865 which is also a fit for your 2010 Ford Fusion. The 4-way stores in the trunk area of your vehicle when not in use so you wouldn't need to come up with a way to secure it to the hitch tube or bumper area. Having the 4-way run out of the back...
view full answer... - Will a Trailer Wiring Harness from a 2011 Ford Fusion Fit a 2014 Ford FusionTrailer wiring harness # 118422 will only fit a 2006 to 2012 Ford Fusion but not the 2014. For the 2014 Ford Fusion you will need trailer wiring harness # 118574. I have included a link to the installation instructions for you.
view full answer... - Replacement Box Recommendation for Tow Ready Trailer Wiring 118422I checked your order notes and you ordered the part # 118422. The converter box changed over the years and that is why it looks different now. You could use the # 119250KIT as a replacement that would just require you to match the wires on the input side of the box by color to the wires you have ran to your shorted out box.
view full answer... - Which Trailer Hitches and Wiring Will Fit on a 2009 Ford FusionWe do have several hitches available for your 2009 Ford Fusion, but part 60254 is not one of them and has been discontinued. The comparable hitch to the one you referenced is the Curt Trailer Hitch, # C11329. You might also be interested in adding the T-One Vehicle Wiring Harness with 4 Pole Trailer Connector, # 118422. This is a T-one style harness that plugs in line with your vehicles taillights and provides a 4-Way connector at the rear of the vehicle. The powered converter requires...
view full answer... - Trailer Hitch that Fits 2009 Ford FusionWe have the Curt trailer hitch # C11329 for the 2009 Ford Fusion that has a towing capacity of 2,000 lbs. This capacity though is independent of the capacity of your vehicle. I tried looking up the capacity for it online and most places say it wasn't listed or it's not rated for any towing. So I really wouldn't feel comfortable telling you that your vehicle could tow a 1,500 lb trailer. Especially on the hills you describe. If you really wanted to do it though I would recommend checking...
view full answer... - Trailer Hitch Recommendation for a 2011 Ford FusionThe hitches available for you 2011 Ford Fusion are Class I hitches like the part # 24865 which has a 200 lb tongue weight capacity. This means that you could carry up to 200 lbs of weight from a wheel chair carrier and wheel chair. Most likely this will not be enough capacity so the only option you would have for this so you would need a small trailer for transporting the lift. A small trailer would be the best route. For trailer wiring you would need the part # 118422, # 3594 for a...
view full answer... - Can a 2010 Ford Fusion Hybrid Tow a TrailerCan you tell me the model year of your Fusion? We do have some hitches that fit the Hybrid models but I need the year to confirm a fit and verify any towing restrictions. Also, any idea of the weight you need to tow?
view full answer... - Can the Foot-Activated Liftgate Still Work with Trailer Hitch Installed on a 2015 Ford EdgeI recommend going with the Draw-Tite Trailer Hitch # 75234 for your 2015 Ford Edge. This is a Class III trailer hitch with a 2" receiver that will not prohibit the use of your foot-activated tailgate although you may have to kick straight out in a different spot than you do now (see attached picture). If you let me know what you will be using this hitch for I can make additional recommendations if necessary. As far as towing with your 2008 Ford Fusion is concerned, I took a look at the...
view full answer...
- Parts Needed to Tow a Trailer with the 2011 Ford FusionYou can pull a trailer with any class of trailer hitch, you just need to be under the weight capacity of either the hitch or vehicle, whichever is lower. Therefore, for your 2011 Ford Fusion I recommend the Draw-Tite Sportframe Trailer Hitch Receiver part # 24865 which has a 200 lb tongue weight and 2,000 lb gross trailer weight rating. Please keep in mind that the owner's manual does not recommend towing a trailer with the vehicle so they do not list any towing capacity. In addition...
view full answer... - Is There A Class II Trailer Hitch Available For A 2010 Ford Fusion The vendors we carry for trailer hitches unfortunately only offer class 1 trailer hitches for your 2010 Ford Fusion. Of the two options available I recommend the Draw-Tite Sportframe Trailer Hitch Receiver # 24865 since the installation process is a bit easier than the Curt Trailer Hitch Receiver # C11390. This hitch has a 2,000lb GTW capacity and 200lb TW capacity. If you were planning on towing a smaller trailer or want to add lights to a cargo carrier or bike rack for better visibility...
view full answer... - Compatibility of Draw-Tite # 24865 Class I Trailer Hitch With 2012 Ford Fusion HybridMy Draw-Tite representative confirms that the # 24865 Class I hitch you referenced is compatible with your vehicle. The fact that your Fusion is the Hybrid model will not affect the installation. The battery will not interfere with the installation. If you're planning on doing some light duty towing, and your owner's manual doesn't prohibit towing, the Draw-Tite # 24865 would be a good choice. You will need the recommended ball mount. You'd also need to add a trailer wiring harness, part...
view full answer... - Can 2010 Ford Fusion Hybrid Tow Trailer and Parts Needed to Do So We do have all the parts needed for your 2010 Ford Fusion Hybrid to physically pull a trailer but you will want to take a look at your copy of the owner's manual for its specific capacity or restrictions. I did take a look at the online version of the manual and found that Ford does not recommend towing a trailer with this vehicle so there aren't any capacities listed. I do still recommend verifying this in your copy of the manual as its possible you have a different model. If you decide...
view full answer... - Can a 2008 Ford Fusion Accept a Class II Hitch to Allow Use of Wheelchair CarrierThe only trailer hitch offered for your 2008 Ford Fusion (a great car - I used to own one until an East Coast blizzard took her away from me) is the light-duty Class I Curt Trailer Hitch Receiver - Custom Fit # C11329 with a 200-lb tongue weight capacity. This hitch does not have the capacity to transport a wheelchair and carrier and no Class II hitches are available for the vehicle. Your option then is to use a small trailer (which will work with one of these Class I hitches). Local outdoor...
view full answer... - Trailer Hitch Recommendation for 2010 Ford Fusion for Towing Small TrailerThe Draw Tite hitch part # 24865 is a confirmed fit for your 2010 Ford Fusion and has a 2,000 lb total trailer weight capacity. This would be more than enough for a 390 lb trailer. Unless there are restrictions in the owners manual of your vehicle on towing this hitch would be a great solution. I attached an install video for you to check out as well. The recommended ball mount but for the Draw-Tite Hitch is # 3594. For a ball you can use # 19256 (1-7/8 inch diameter) or # 19258 (2...
view full answer... - Will Brophy 4-Way Bracket BK4F Work with 4-Way of Tekonsha Kit 118422Yes, the Brophy 4-way mounting bracket part # BK4F is compatible with the 4-way that comes with the # 118422. The Brophy bracket will also bolt up to the no drill mount bracket # 18140 you referenced as well.
view full answer... - Hitch Recommendation for a 2011 4-cyl Ford FusionThe Draw Tite Hitch part # 24865 has the towing capacities of 200 lbs tongue weight and 2,000 lbs total trailer weight. Whether or not your 4-cylinder 2011 Ford Fusion has the same capacities is why you need to consult the owners manual of your vehicle. Whichever component in your towing setup has the lowest towing capacity is what dictates the towing capacity. I attached an install video for this hitch for you to check out as well. For trailer wiring you would want the part # 118422. For...
view full answer... - Trailer Hitch and Wiring Recommendation for a 2011 Ford FiestaThat depends on which model of Ford Fiesta you have. If you have a sedan you would want the part # 24856 and if you have a hatchback you would want the part # 24961. For trailer wiring you would want part # 118471 for if you have a hatchback and part # 118422 for if you have a sedan. For a ball mount you would want the part # 3593 that you referenced. For a 2 inch ball you would want part # 19258 or # 19256 for a 1-7/8 inch ball.
view full answer... - Trailer Running Lights Not Working On a Trailer Towed by a 2011 Ford FiestaIt sounds like the running lights are not working on the trailers. Since they are working fine with the other vehicle, this indicates a problem with the other vehicle and/or its wiring harness. You can test the wiring harness to see if it is faulty using a circuit tester like # PTW2993 if needed. Also, make sure that you are using the correct wiring harness. The hatchback models can use the 56064 but if you have a sedan, you would need a different harness like # 118422 or # C56114. If...
view full answer... - Hitch Comparison and Recommendation for a 2008 Ford FusionThe Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # C11329 is absolutely the correct hitch for your 2009 Ford Fusion! In case you don't have a ball mount yet you would also want the part # 3592, and then for a 2 inch ball # 19258 and for a 1-7/8 inch ball # 19256. For trailer wiring you would want the part # 118422.
view full answer... - Trailer Hitch and Wiring for a 2006 Ford FusionThat was a nice gift but Hidden hitch trailer hitch 60282 will not fit a 2006 Ford Fusion. It used to fit 2010 to 2012 Fusions, 2010 and 2011 Mercury Milans, and 2010 to 2012 Lincoln MKZs. But that hitch is now discontinued. The comparable trailer hitch for the 2006 Ford Fusion is the Curt # C11329. If you plan on doing some towing the correct ball mount is # 3592. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. For trailer wiring use # 118422. I have linked a video...
view full answer...
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
Test Fit:
Joe V
Test Fit:
Nicholas E
Test Fit:
Alan C
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Video Edited:
Zack K
Video Edited:
Andrew K
Video Edited:
Joshua S
Video Edited:
Chris R
Installed by:
Jeff D
Updated by:
Laura H
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Isabelle B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Marc
4/3/2014
The products are great. No complaints what so ever. I figured it was best to get 200 dollars worth of towing equipment for my quad and trailer than to spend 45k for a brand new truck! Thanks for the follow up.