Part Numbers: 90885,3040-P
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This proportional brake controller keeps it simple with intuitive controls that are easy to use. Includes a large, digital LED display, 3 boost levels, battery protection, and continuous diagnostics.
Features:
Specs:
You can adjust the gain (also known as output) with the thumbwheel on the front of the controller. Gain lets you set the maximum amount of power that will be applied to your trailer's brakes. A heavier trailer will need more power to achieve smooth, safe braking, while a lighter trailer will need less. Typically, the gain is only readjusted when you experience changing road conditions or if the weight of your trailer changes.
The boost setting controls the aggressiveness of your trailer's braking, meaning how quickly the brakes reach the maximum braking level. You can adjust this when you're towing heavy loads and you need more umph to bring your trailer to a stop. Your tow vehicle doesn't need that much power to brake in time, but your heavy trailer does.
Depending on the level of boost, your trailer brakes can start at either 13 percent or 25 percent of the set gain. What this means is that, instead of starting at 0, the brakes will start at 25 percent and get to100 percent sooner. This keeps the trailer from pushing your tow vehicle forward.
If your trailer weighs less than your tow vehicle, no boost is needed. But, if you want your trailer to lead the braking, you can select level B1.
Boost Levels:
| Approximate Gross Trailer Weight | Boost Level | Increase in Initial Power Output |
|---|---|---|
| Less than tow vehicle GVW | B1 | 13% |
| Equal to tow vehicle GVW | B1 or B2 | 13% or 25% |
| Up to 25% more than tow vehicle GVW | B2 or B3* | 25% |
| Up to 40% more than tow vehicle GVW | B3* | 25% |
*Both B2 and B3 offer a 25-percent boost in initial power. But the braking curve for B3 is more aggressive than that of B2. This means that, even though you will start out with the same intensity when using these boost levels, you will get an overall more aggressive braking experience with the higher level. So if you use B3, you will reach maximum braking sooner than if you use B2.
Safety Features
The Prodigy P2 offers key safety features to prevent damage to various components of your towing setup. Integrated reverse battery protection shields the brake controller and your trailer's breakaway system from shorts. When the P2 is not in use, it will be in power-saving mode. In this setting, it draws only 3.6 milliamps, minimizing drain on your vehicle's battery.
The P2 also comes equipped with a hold feature to prevent wear on your brakes. When you're waiting at a red light, you don't need your trailer brakes on at full power. The longer you sit there, the more they will overheat. But with the P2, any time your tow vehicle and trailer are at a standstill with the brakes applied for more than 5 seconds, the hold feature will kick on and reduce power to just 25 percent. This will keep your trailer in place while saving your brakes.
The P2 keeps the manual override within easy reach, great for stopping sway or controlling your trailer's momentum in emergencies. To engage the manual override, just twist the rotary-style lever from right to left. This will activate the trailer's brakes and brake lights without you having to apply the brakes on your tow vehicle, perfect for limiting trailer movement while you're cruising.
The Prodigy P2 also offers diagnostics such as:
The self-leveling feature of the P2 ensures that the brake controller continues to function even as you drive up steep hills or through the mountains. Simply mount it in your cab at any vertical angle, and the controller will level itself automatically thanks to its 360-degree rotational range. This makes the installation that much easier. But keep in mind that the P2 must be horizontally level and parallel with the direction of travel to work correctly.
Installation is a snap. After mounting the P2 unit in your cab using the included bracket, hardwire one end of the included pigtail harness directly into your vehicle. The other end plugs into the brake controller. To remove the P2 for storage when you're not using it, just unplug the unit and slide it out of the bracket. With a replacement wiring harness (sold separately) and replacement bracket (P7685 - sold separately), you can even transfer the Prodigy P2 to another vehicle.
Installation Accessories
For even easier installation, a vehicle-specific specific wiring adapter is available for most newer trucks and SUVs. One end of the custom adapter plugs into your vehicle, and the other end plugs into the controller - no hardwiring required.
See also etrailer.com's exclusive 7- and 4-way brake-control installation kit (ETBC7 - sold separately) if you don't already have a 7-way plug at the back of your vehicle.
Note: If a custom brake control wiring adapter is not available for your vehicle, one of the following will be required:
20-Amp circuit breaker (9506P - sold separately) for 2- to 4-brake applications
30-Amp circuit breaker (38630 - sold separately) for 6- to 8-brake applications
The Tekonsha Prodigy P2 brake controller comes equipped with proportional braking to give you the best towing experience. Proportional braking means that your trailer brakes mimic your tow vehicle's brakes. If you slam on the brakes in your vehicle, your trailer brakes will activate with the same intensity; if you brake lightly, your trailer brakes lightly too. The trailer's braking is in proportion to your vehicle's braking. This saves wear and tear on the tires and the brakes on both your vehicle and trailer.
The Prodigy P2 uses an internal inertia sensor to detect how your vehicle is braking so it can send the right amount of braking power to your trailer. It measures the inertia of your tow vehicle and activates the trailer's brakes to slow at the same rate. The result is uniform braking across your towing setup. No push-pull action - just smooth, proportional braking every time.
California residents: click here
Install your electric brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in harness beneath your vehicle's dash.
Features:
This adapter plugs into the 5-pin connector on your vehicle's built-in brake control wiring harness. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal.
To install your electric brake controller you need to connect the wiring of the controller to your vehicle. Certain manufacturers offer pre-wired options, typically known as tow packages, wherein these wires are run for you from the dash to the trailer connector on the back of your vehicle. Often, a brake controller wiring harness is included with your tow package. This harness plugs into a port beneath your dash and connects to the four wires of the brake controller. If, however, you have a brake controller with a plug in place of the four loose wires, you can use the Tekonsha adapter.
This adapter requires no hardwiring. It is designed to plug directly into your electric brake controller for the simplest installation possible. Because there are no wires to connect, installation is not permanent. You can unplug and remove your brake controller at any time and securely stow it away.
California residents: click here
Average Customer Rating: 4.9 out of 5 stars (3998 Customer Reviews)
This proportional brake controller keeps it simple with intuitive controls that are easy to use. Includes a large, digital LED display, 3 boost levels, battery protection, and continuous diagnostics. Install your electric brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in harness beneath your vehicle's dash.I purchased the brake controller and wiring harness from you all and installed it watching the video on your website. I followed the instructions to an absolute T. Got everything ready and tested the product and got an SH error code for the blue brake wire shorting out. I pinned and measured resistance and everything was coming back fine (4+ ohms resistance). I then hooked a power prope to it to find the short along the frame and nothing. I had power from the female connector all the way up to the brake controller. After 4 hours of troubleshooting, I found that the female trailer connector was shorted internally. See the attached picture. The blue and green ring terminals inside of the female trailer connector were touching. Replaced the trailer connector and now all is well.
Arrived as promised it was easy to install I have tried it out a couple times on my 7X16 cargo trailer. Today I think I have set it up properly for my truck and trailer at B1 at #12 boost level. It never locked up trailer brakes but I believe it is right. Installed on 2014 4x4 Tundra with 4.6 V8 etrailer sent hook up wire to fit Toyota receptacle which was behind driver side kick panel. Grounded to gas pedal bolt, mounted unit under dash on right side of steering wheel.
I had a Prodigy P2 controller in my last pickup and was really pleased with it. So wanted to install the same thing in my newer truck Everything worked smoothly on installation. Made the necessary adjustments to controls after hooking to the trailer and it works great!
This is the second one I purchased. The first was 10 years ago and installed in my 06 GMC. It has worked flawlessly allowing for safe and smooth stops from normal braking to a few of the panic stops that had to made over the years. The new owner of the truck likes the way it works too. I have multiple trailers and with one initial setup on the lightest trailer was able to tow all of them without changing anything but the boost setting to compensate for the different trailer weights.
When needing for a controller for my 07 Silverado there was no other unit that would fill the bill. This P2 looks the same except for the blue display instead of the red. The install took 20 minutes using the direct fit cable ordered with the controller. Setup was easy as with the first unit. I wanted the placement above the parking brake pedal so the OBD II connecter had to be moved. I did the same with the 06 GMC. It is a comfortable place to reach and it keeps the light away from the passenger's eyes at night.
As good as the Tekonsha controller is it is even a sweeter deal buying it from etrailer. The quick shipping, excellent pricing and knowledgeable staff are second to none in customer service.
Installed this in my 2015 Jeep Wrangler Unlimited Sport. I thought that I would add some input on installation that would help others.
I found a way to route the power distribution wires in the frame of the Jeep that did not require the use of a fish tape. If you look at the frame just behind the rear tire you will see a hole in the face of the frame. Start pushing the wire bundle foreword. It will rise up and over the U shaped frame portion of the rear axle and then down along the passenger compartment area. About there, you will be running out of pushing stiffness. Look for the wire bundle to appear at a similar hole in the frame in that area. Grab it a and pull out approximately 4 feet and then push it right back in the same hole going foreword. This time you will look for the wire bundle to appear at again a similar hole just foreword of the driver compartment. Now is the time to grab it and start heading up to the engine compartment outside the frame. Do the same procedure for the wire going aft for the plug end of the installation. For the wires going through the firewall, Jeep has conveniently added a nice foam lined hole to route wires through. You will see this hole position in the attached photo with a green wire coming through. The plastic cover around the steering column pulls down from the top and hinges at the bottom. Remove the metal plate with two bolts to get to the brake switch. Twist and pull the brake switch out foreword and go for the brown stripped wire as your brake circuit. Do order the LONG frame bracket adapter for the switch plug at the rear. To drill the steel for the supplied plug bracket just takes too long. Now that you have it installed you will notice that the power will remain on the unit after you turn the key off. Don't sweat this as it will not stay on long. I doubt a few milliamps draw is going to kill your battery!
The online video showing the installation of the Prodigy P2 trailer brake control into a 2011 Ford Ranger was excellent! It made the installation into my Ranger simple and straight forth.
I have yet to hook up to my travel Trailer and adjust it for brake setting, but all readout displays thus far are as stated in the instructions.
Having previously installed the trailer connector, I did not purchase the installation kit and in retrospect for cost effective and simplicity would recommend anyone to purchase the kit along with the controller.
I believe I am going to be very pleased with this product.
Thank you
I have a Tekonsha controller on my 2001 Chevy Silverado and it worked like a charm for over 18 years.I'm sure that the new Prodigy P2 will do the same.
It would be easy to have this part order and install on the Tundra. i went one step further and end up using the wiring in the box with P3 Trailer brake and had to splice the wiring to make longer extension in order to install the P3 in the empty slot between the lighter and 12v socket which make is more customized look and out of way. Would be cool if they offer longer version for someone who want to install it somewhere else behind the driver's spot zone.
Purchased brake controller for my 2014 Tuna. excellent order/shipping/receiving time.Received everything I needed with order in a very timely fashion. Website made it very easy to find and decide on exactly what I wanted. Etrailer will be my first choice for finding the accessories I need in the future. Purchased Tekonsha P3 brake controller and is the best thing to a factory installed controller I have encountered.
Henr L.
12/28/2017
WOW! Somebody that actually cares! This email was a real surprise. Yes I amstill using the controller and it works better than any I have ever owned. Idefinitely recommend I as well as etrailer.com to everyone interested.Thanks for caring about your customers!
Pictures of the install. Approximately a 20 min job. First picture my finger is pointing to the factory plug with the etrailer supplied harness plugged in. Note the harness did not specify that the white common with the ring terminal should be connected to ground. But then again that SHOULD be obvious. I will be towing this weekend so I will rate the product then. One minor gripe is that there is always power to the unit which is a battery drain (as evidenced with the key out of the ignition and the unit stayed on) Not sure as to the impact but the controller can always be unplugged or removed.
Sorry for the dirty floor mats in the photos.
Patrick B.
1/30/2014
Just a quick note, the controller has an automatic shut-off. After 15 minutes of the truck powering off and sitting still, the control powers down. As soon as it sees movement, it powers back on.
Trevor
6/29/2014
So you ran ground to negative side of battery? Or just on the frame interior somewhere?
Rachael H.
7/1/2014
very nice controller, very smooth and you don't have to mount it flat!! e trailer is the best company i ever worked with. they have pics, video, email support(exellent) and just flat out make it easy for you to do it yourself instead of paying some dirt bag $300 to install at your local trailer shop. i also installed kit #ETBC7 and once agian it was awesome. COMPLETE with DETAILED directions. i'm not a mechanic or hack employee at local trailer shop....BUT dealing with etrailer and there parts made my install very easy and CLEAN!!!
I use this brake controller for my 2007 Tundra hauling a 6x10 dump trailer. I’m very pleased with the product, it works great. The only thing I notice is that you have to be very aware of your load, dialing in the right number for your weight. I could be at 4.8 and my trailer tires will lock up. Go down to 4.6 and they’ll be good. That’s the only thing I notice.
Perfect for 2011 lexus gx460
Marilyn
6/15/2024
still works great
the controller has great reviews, I got it because my factory controller wasn't working well with the new camper that has electric/hydraulic brakes and I was experiencing a 5 second lag for the trailer brakes to come on. this controller works better with a 2 to 3 second lag, need to try a couple different combos on settings, have the boost at 3 (per recommendations) and gain at 2.5 and under hard braking it locks up the trailer tires. going to try boost on 2 and bump up the gain and see if that works better.
Been one year of ownership now and this controller has performed very well. I would by again for sure.
Install is very easy once you locate the vehicle's brake controller plug. The plug in a Tacoma is extremely well hidden. It is high above the driver's side kick panel taped behind a plug wrapped in foam. I have attached a photo to help you locate it in a late model Tacoma. Once I found the plug, the install took less than 20 min. The controller works great.
Mark N.
6/5/2015
Very well
Great product! Since I pull my goose neck with electric brakes, with my semi truck tractor, it acts as a interface between the air brakes and the electric trailer brakes, and acts as a Johnson bar if I need to get the trailer back under control.
We ordered a part for the 2008 Land Cruiser and was told that it's the same installation. IT IS NOT! The connection to the harness is not in the same location as Tacoma. After looking for more than an hour, I got smart and found some info on another website. Even the manufacture has the info wrong. So, if you have a 200 series Land Cruiser, your plug is located under the dash behind the switches for the mirror. You will need to take apart the lower dash panel and then push out the switch panel. There is no need to detach any switch, it all hangs out just fine. See photos for the location of the plug. Plug the adapter in from there you can follow the instructions.
Patrick B.
9/10/2013
Thanks for the awesome review. Good info and really helpful for Land Cruiser folks.
Great product, very easy install especially with the OEM harness. In about an hour had it installed and trailer set up with controller. Thanks,
Greg
I didn’t have a good location that was reachable while driving so I mounted the controller on top of the dash. I leveled the bracket with a spacer and ran the harness by an access panel. I used about 70’ of the duplex wire due to running the cable to front and then back to the house batteries inside the coach.
The access panel made it easy to make the connections and run the wires through the firewall.
I mounted the 40 AMP and 30 AMP circuit breakers up front in the main fuse panel box. I drilled a hole through the box and firewall to run the wires from the brake controller to the breaker and to the blue wire for the tow connection at the back of the coach.
I ran the battery connections to my house batteries up front instead of using the engine batteries in the back.
I found the brake connection wire under the coach in front directly below the brake pedal.
I mounted the converter in a beam in the back with lots of zip ties
Great Brake Controller This was my first time using a brake controller and installing one as well. The directions were easy to follow for both the install and setup.
2012 Ram
Used in conjunction with harness kit for my 2002 tundra, this year has no provisions for towing trailer with electric brakes.
The controler itself has proven itself nicely, with no issues with installation or use, adjust easily.
The mounting location I chose may have some slight interference issues with legs on taller people, but I have not had any @ 5'11". The truck is a midsized so room is more limited. I'm towing a tandem 14' trialer with 4 seat RZR, tracking and stopping is perfect, even under hard breaking.
The Tekonsha Prodigy P2 Brake Controller arrived on time and is just what I needed. The installation and operating instructions are easy to understand and should make installation a breeze. I'll give an update after I get it installed.
I sell and install a variety of components for various companies and individuals. I have zero comebacks from this company. Not that I haven't received defective parts but they always make it right. And that is good business.
Great Brake Controller, used it with the Universal Install Kit for Brake Controllers and No-Drill Mount Bracket, Short - 18140. It only took me 2.5hrs to have it fully installed in my Jeep Wrangler Unlimited 2013. Videos were great. Also having some 1/4in water tubing helped for phishing wire thru frame.
Wish I had watched the video a couple of times before buying and also purchased the extra wire to go from the battery to the brake controller, but had extra wire from another project that worked.
This brake controller works great as we tow a <3500lbs Travel Trailer with our Jeep.
Comes with a great card that helps with settings, keep it in the glove box for future reference.
Ask the Experts about this Trailer Brake Controller
Do you have a question about this Trailer Brake Controller?
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Gregory U.
8/9/2017
Product been working great. I even kept the console part and move it newer Tundra truck that I brought and bigger camper. Work better than I expected. I did use the bracket that come with the controller and mounted it. So I wouldnt have to worry about it coming loose or being in so far in the console. It also allow me to use the manual brake easily.