Is The Tekonsha 3040-P Wiring Adapter Supposed To Have A Ground Strap Like The 3041-P?

Question

Question:

Have a 2019 Toyota Sequoia. I have a Tekonsha P3. Looking for correct brake controller adapter. You show 3040-P, but your photo appears to be the 3041-P because it has the extra ground wire. Does the one you recommend have this ground wire? Does it hurt to have this extra ground wire? Thanks

asked by: Jake C

0

Expert Reply:

The Tekonsha Plug-In Wiring Adapter # 3040-P is supposed to have the additional ground strap for your 2019 Toyota Sequoia. This was something that was not always on the harness but was added some time ago as the factory wiring ground was insufficient. This will allow you to properly connect your Tekonsha Prodigy P3 Controller # 90195 to your Sequoia.

While it will look similar to the Tekonsha # 3041-P they are not interchangeable as they terminals are different.

expert reply by: Bud M

0

Answer 1

For your 2000 Ford F-250, the fuse location 1 is a 20 amp fuse for turn/hazards in your fuse box. There is also a fuse for trailers that is a 7.5 amp fuse also in location 1 and location 3 of the other fuse box. Anything beyond those fuses will be a…

view full answer...

Answer 2

For your 2023 Toyota Tacoma I recommend the Tekonsha Prodigy P3 #90195. This is a fully proportional dash mount controller and can control up to 4 axles at once, so this will work great for your 2 axle trailer. Large accessible buttons and an LCD…

view full answer...

Answer 3

As long as you stay under the 10,300 pound mark you should be fine. Currently your trailer and gear estimate would weigh 9,100 pounds. Take a look at the rig when the trailer and truck are fully loaded as though you were ready to hit the road. If the…

view full answer...

Answer 4

The individual links on a weight distribution system like the #RP66541 do not represent different tongue weight values. It really just comes down to following the setup procedure that is outlined in the install instructions which are attached which…

view full answer...

Answer 5

Since you have a plastic bed liner in your 2012 GMC Sierra 2500HD you will have to trim the liner in the foot print of the bed rails in order to install the kit, #C16411-204, in the truck. Plastic bed liners do not provide a stable surface which is…

view full answer...

Answer 6

In order to install a 7-way trailer wiring harness in the bed of your 2010 Ford F-250 while also still allowing for the factory 7-way at the bumper, you are going to want to use the Curt 5th Wheel/Gooseneck Custom Wiring Harness part #C56070. I have…

view full answer...

Answer 7

I checked with Curt and the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector - 7 Long Item #C56070 would require 7 inches of clearance on the inner side of the fender/bed wall to install.

view full answer...

Answer 8

If your 2018 Toyota Tundra has the 6-1/2 foot bed, I recommend the Curt Custom Fifth Wheel Installation Kit #C16468-204. This installation kit includes custom-fit brackets that are confirmed to fit your truck and will use existing holes in the…

view full answer...

Answer 9

Yes you can setup the Tekonsha P3, #90195, without a trailer connected. However, you will most likely need to do some fine tuning once a trailer is connected to get the proper amount of power back to the brakes for the particular trailer and load you…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Is The Tekonsha 3040-P Wiring Adapter Supposed To Have A Ground Strap Like The 3041-P?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching