Brake Controller and Install Recommendation for a 2015 Mercedes Benz Sprinter and 2005 Honda Pilot

Question

Question:

I want to use Tekonsha Prodigy P2 Trailer Brake Controller 90885 for 2015 MB Sprinter 2500 with MB factory trailer hitch and 7 pin plug. Which Plug the brake control end of wiring harness into back of brake control and vehicle end into vehicles port will work? AND connecting the same unit Brake Controller 90885, to 2005 Honda Pilot with factory hitch and 4 pin which I need to change to 7 pin? Which Plug the brake control end of wiring harness into back of brake control and vehicle end into vehicles port will work? Code: 3070-P? Thanks,

asked by: Joe

0

Expert Reply:

Since you have a 7-Way in your 2015 Mercedes Sprinter you will only need a few more components to complete a brake controller install on your vehicle.

First let's start with a brake controller. I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup.

Next, for a wiring kit to install the brake controller and the 7-way adapter you would want the Wiring Kit for 2 and 4 Brake Electric Brake Controllers # 5506. This will provide the power source and ground for the wiring for the brake controller. You will need to test the wires from the brake pedal switch of your vehicle to find a circuit that has voltage when the brakes are applied and none when not applied. This will be the circuit you will run the red wire to.

Finally you will need to run a length of 10 gauge wire (part # 10-1-1) from the brake output circuit of the controller to the brake output circuit of the 7-way (blue wire). The # 10-1-1 is sold by the foot so you will need to order a quantity of the amount of feet you will need.

I attached an FAQ on installing brake controllers for you to check out.

To install the brake controller in the 2005 Honda Pilot will require the part # ETBC7. I wish there was a plug and play option for this vehicle but this would be the only route. I did attach an install video that shows this install in a very similar 2003 Honda Pilot.

expert reply by: Jameson C

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only…

view full answer...

Answer 3

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 6

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A factory 7-way trailer connector isn't all you need to power a trailer's electric brakes. You still need a brake controller. Some Ford F-150s are equipped with a factory integrated brake controller, which you may have. If your 2012 Ford…

view full answer...

Answer 9

You are correct, you should only be getting output when the brake is applied, or the override switch is activated. It sounds like the controller might be bad, but to make sure, you should probably bench test it before tossing it. Use a circuit…

view full answer...

Answer 10

On a 7 pin round which is the common connection on a semi trailer, the clearance/marker lights are at the 10 o clock position when you look at the trailer wiring connection. When looking at the connector on the back of the truck, that will put the…

view full answer...

Answer 11

From what I could find, it looks like the plug for a trailer brake controller on your 2023 Nissan Frontier is located in the same location as the 2022 model year. That is behind the side panel by the OBD connector and is likely pushed back into the…

view full answer...

Answer 12

There are a number of factors involved when converting a semi 7-way to an RV 7-way. Semis generally use a 7-pin round pin socket, similar to #PK11720. And RV style 7-way uses blades, like #PK12706. We do not offer any pre-made adapters to make this…

view full answer...