T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
(243 reviews)
Price: $75.96
In Stock
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
Item # 118405
Retail:$86.65
Our Price: $75.96
You Save: 12%
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (243)
- Q & A (0)
- Photos
Tekonsha Custom Fit Vehicle Wiring - 118405
- 4 Flat
- Trailer Hitch Wiring
- Custom Fit
- Powered Converter
- Tekonsha
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring. Powered ModuLite reduces strain on wiring system.
Features:
- Provides a 4-way flat trailer connector at the back of your vehicle to power your trailer's signal lights
- Compatible with 5-pole, 6-pole and 7-pole adapters (sold separately)
- Connects quickly and easily
- Locate connection points in rear cargo area
- Plug in T-connector
- Run hot lead to car battery
- Includes ModuLite to ensure that your vehicle's wiring matches that of your trailer
- Powered module connects directly to battery to avoid overloading vehicle's electrical system
- Constructed of 16-gauge bonded wire
- Comes with dust cap for 4-way flat connector
Specs:
- Maximum amperage:
- Stop/turn lights: 2.1 amps per circuit
- Tail lights: 5.6 amps per circuit
- 1-Year limited warranty
Installation
This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located inside your trunk or cargo space, behind the tail lights on both the driver's side and passenger's side. You will need to remove some interior trim or carpeting to access this harness. Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery and insert the provided fuse.
Once installation is complete, the 4-way flat connector will be stowed within your trunk or rear cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
ModuLite Powered Tail Light Converter
A ModuLite power module is built into this T-One connector. Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of your trailer. This power module functions as a tail light converter to combine the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
With a ModuLite, your trailer's lights will be powered without overloading your vehicle's electrical system. Because the module draws power directly from your car's battery and bypasses the electrical routes that are used by a basic wiring harness, there is virtually no draw on your tail light circuits.
118405 Tow Ready T-1 T-Connector - 4 Wire - Modu-Lite
Installation Details
California residents: click here
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- etrailer mistake
Customer Reviews
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector - 118405
Average Customer Rating: 4.7 out of 5 stars (243 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring. Powered ModuLite reduces strain on wiring system.by: James 11/25/2022
Wiring harness install was easy. This is my fourth or fifth vehicle I've done this type of install. Viewed YouTube Etrailer for install video.
by: Christopher11/27/2020
2017 Mazda 3
I have a 2017 Mazda 3. I ordered the product because I was hesitant about splicing into my car’s wires. This wiring harness made things a lot easier. I watched a YouTube video to get a quick idea of how to do it. The only thing I did different was I ran the wire which connects to the battery through the inside of my car. The wire runs from the trunk, easily squeezed between the rear seat, tucked into the floor panels by the doors, goes up near the driver side, through a small pre-existing gap in the body and to the battery. No drilling though the firewall, no need to go beneath the car. See photos for reference.
Christopher
11/28/2021
Still works great. Got exactly what I paid for. Extremely satisfied!
by: Ronald03/23/2023
Easy to install. Fit and works great
Ronald
5/9/2024
Easy to install works great
by: Rob08/18/2016
Mazda Protege5
My second hitch purchased from etrailer for a Mazda hatchback (first '02 Protege5, now '15 Mazda3). Both good experiences.
Very easy hitch install, the inclusion of the fish wires for the frame hanger bolts is a stroke of genius. Don't be afraid of the exhaust isolators, just spray some soapy water and support muffler with a jack or strap. If you can change a flat tire then you can work a wrench well enough to do this in an hour.
'14-15 Mazda3 has a couple of things making wiring easy to integrate. There's a grommet in the left rear quarter floor that's perfectly placed. Just trim some electrical tape to allow an opening, clip the new connector near the lighting adapter & reconnect inside after fishing from outside. I ran power neatly along driver's side rocker & out through the firewall. It's both easier and less vulnerable, just fish one more wire through the mass that exits above the driver's left foot. (Just DO NOT use anything sharp, you don't want to nick any wires and short something out). Finally the battery on my car already had several open connections to use right at the positive terminal, each protected by a fusible link no less! (See photo.) All I needed to add was an M6 stainless nut to connect the new wire.
Only a couple of minor downsides:
Aesthetically this is one of the uglier installs, mostly because the 3's huge muffler is right against the rear valence, leaving no room to tuck anything out of sight. My Protege5's hitch was entirely hidden except for the receiver. Here, unless you're willing to butcher your bumper cover (assuming there's a hitch made to fit that way) you're stuck with what you see in my picture. I saw the round-tube alternative on another similar car and it looked a little better, but that one requires support straps for a rack with any carrying capacity.
Design-wise I ran into one surprisingly annoying thing the first time I went to insert my drawbar. The hole in the receiver for the hitch pin is set really close to the hitch frame, and there's a gusset plate on top, which leaves basically no room for the clip that secures the pin. My existing clip didn't fit at all until I ground the ends a little. The clip that came with the new hitch sort of fit, but only jammed up against the hitch so hard that it scratched right through the protective powder coat. Weird in a product from such an experienced manufacturer, but easy to rectify.
by: Purvis04/10/2024
Received package 2 days early. The how to video on u-tube was very helpful. I am very pleased with etrailer. Thanks alot.
by: Dave H.06/01/2024
This was a good recommendation from the etrailer expert. Installation was straightforward (although a little more involved than I remember from last time. He told me it is more reliable than my Curt product that had failed.
etrailer is a company I always look forward to dealing with.
by: Tim09/03/2019
2017 Toyota Camry
All equipment was delivered on time. Hitch, wiring harness, receiver and ball. Watched video's on installation of harness and hitch. Went down to my garage and installed both with the help of my girlfriend. Very satisfied with the products and the installation. etrailer supplied the goods and the knowledge. I am very happy that I went this route.
by: Heidi04/15/2020
Hitch installed easily on my 2014 Toyota Corolla.
Wiring had poor instructions in the box but the video posted on etrailer’s site answered my questions.
No issues and everything worked.
Thanks.
by: Keith 05/23/2024
2009 Toyota Camry
Great part, great service
by: Keith 08/29/2019
2014 Toyota Camry
Great product. This is my fourth one from etrailer. A bit more difficult to install. Had to think up some way to hold it up singlehandedly, but managed it. See attached picture.
Will deal again with you in a flash.
by: William 09/11/2023
2014 Mazda 3
Good product. Printed Instructions a little confusing but online directions were excellent.
by: Donald02/21/2024
2019 Toyota Corolla
Harness arrived rapidly, faster than Amazon. Looks to be a simmple installaion.
by: Sean 03/26/2024
Easy install. Fits perfect.
by: Bryon 02/10/2024
Well it worked
by: John06/07/2023
No instructions for my vehicle
Jenny N.
6/9/2023
I am sorry that the instructions were missing. I will send you a copy via email and it can also be downloaded from the product page. It is in link towards the bottom of the page before you see the reviews. We also have a video install on a 2016 Toyota Corolla.
by: Fred10/20/2022
The harness works great once installed. Printed installation instructions were general for many vehicles and woefully inadequate . On my Mazda 3 wagon I ended up drilling a hole through an internal body panel and lining it with a rubber grommet for the wire to pass through rather than running the wire between the tail light assembly and its receptacle(?) in the body panel as instructions indicated. The foam lining around the edge of the receptacle was thinner than the wire and I'm sure the wire would have been crushed between the tail light assembly and the edge of the body panel opening, and eventually short out.
by: James 01/30/2023
It took four times to order because your system had my old address and finally after I talked to someone who knew what to do and he placed the order!! Although I had to pay for half of shipping!! I would like my shipping amount reimbursed!!!!
by: David 10/02/2023
2014 Toyota Corolla
Package came on time and it was exactly what I ordered. Very pleased.
by: Len S05/04/2015
2014 Toyota FJ Cruiser
Installation is a little tedious due to tight spaces to get to existing lights. I do not understand the purpose of requiring a power source. I have stalled other wire harnesses in the past that just connect to the existing lights and on your way.
Patrick B.
7/30/2015
The purpose of the power feed is to isolate the power draw to a dedicated line. This way, if there is a short on the trailer the subsequent overload happens on the dedicated power wire, blowing the fuse, and preventing over-draw on the vehicle wiring. If the trailer lights got their power through the vehicle tail lights power, then a short on the trailer would over load those circuits potentially damaging the vehicle wiring or lights.
by: Katelyn04/03/2020
2011 Toyota FJ Cruiser
So I’m a woman and I could install this, so it’s that easy to follow. Needless to say my husband was a bit impressed. I won’t lie the wire connectors were a bit hard to clamp and connect but otherwise everything was super easy to install and works great!
Katelyn
4/5/2021
Still works fantastically, I haven’t used my trailer much during the winter, however during the fall it was still holding up quite well. I still highly recommend this product!
by: Tom 09/09/2022
Great trailer hitch, works great. Had it installed by a local gas station, really like the simple attachment process for both hitch and lights hookup. I highly recommend this product.
by: Chuck11/13/2016
2004 Mazda 6
Good product. Good price.. a little ghetto how the light wire for the trailer needs to hang out of the truck when using the trailer but that is normal for the car. After a year it works well the wire sit fine in the truck seal and never gets a cut in the wire which I was afraud of.. great set up and I would recommend it to anyone for the price.. I use the wiring and hitch on a Mazda 6 with a large 10 foot trailer and it works great.. oddly the car even handles the trailer well. Very happy
by: Kern11/13/2017
Mazda
This wiring kit was purchased for installation on a 2017 Mazda 3 sedan.
As received, the installation instructions made no reference to any Mazda 3. There was reference to a Mazda 6 with incomplete instructions and pictures. The company web site offered no further clarification.
I am an automotive engineer with an electrical background and the installation was far from obvious. Wire color codes did not match the car harness. The power wire to be routed to the battery was black. Vehicle power is usually red. The fuse holder and its wiring to be atttached to battery plus was yellow. The power wire leading into the control module was red. So, we have a yellow wire connected to a black wire, connected to a red wire. What a mish-mash!
I finally called the manufacturer and spoke with a customer service representative. He was not able to help immediately but took time to find the right information and called back.
Once the install information was received, the installation went reasonably well with the most difficult part being the routing of the power wire forward to the battery. To protect the wire and install it securely, I removed the plastic undertrays and routed the wire alongside some fuel or hydraulic lines. As mentioned by other users, more ty-wraps would have been useful. I used some from my existing supply.
After install, I tested the function with the boat trailer and it appears to work as designed.
by: Joe A04/28/2020
I was very impressed with this trailer hitch. the quality the ease of installment and wiring harness. The hitch held up just fine for the past year, I would recommend this to anybody. I use it often to pull my 12 foot boat and my utility trailer and it’s only a 1 1/4 hitch on my 2015 Toyota Corolla.
Thank you for a great product
by: Essais05/18/2018
2014 Volkswagen Passat
My third hitch from etrailer: 2000 VW Passat, 2006 Mazda 3 Sedan, now 2014 Mazda 3s GT. In all three, the plans and fit-up were excellent. For the 2014 Mazda 3s GT, I bought the 24914 Draw-tite hitch, with 3493 draw bar and 19256 ball. With the standard chrome exhaust tips, I had to lower the muffler for the hitch mounts to clear the exhaust. This was the most difficult part -- windex for lubrication and a strong grip pulled off the four rubber muffler hangars, lowering the muffler on a floor jack about 6". The hitch then fit perfectly to the mounting holes, and the part metric, part SAE hardware provided was high grade and correct. Fishing the mounting bolts through the frame members was the simplest part. Tightened nuts, raised the muffler, and then lubed and pushed on the hangars again. Done in about two hours. Four ibuprofen in anticipation of sore muscles. Nothing new. Top of the draw bar at the hitch is at 11" from the ground, putting the drawbar top at 13-1/4".
I installed the 118405 wiring harness without problems, choosing to route the power wire for the switch "converter" along under the interior trim under the doors and into the interior fuse box compartment, then into the engine compartment by a single hole punctured through an existing rubber nipple just above the wiring feedthrough on the firewall. I changed the ring connector to a 1/4" ring connector to match the existing 6 mm post on the Mazda battery terminal block (thank Mazda for the ready-made posts for accessories). Works!
Once again, etrailer gave me all I needed in one shipment, and everything fit as planned. No problems pulling my lightweight sailboat trailer and utility trailer. Another satisfied customer!
25
243
Show More Reviews
See what our Experts say about this Tekonsha Custom Fit Vehicle Wiring
- Recommended Hidden Hitch For A 2015 Mazda 3 SedanWhen it comes to installing a trailer hitch on your 2015 Mazda 3 Sedan that is completely hidden I recommend The EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - 2 inch # 306-X7303. The trailer hitch has an easy, bolt-on installation with no drilling required, and has a black powder coat finish that offers superior rust protection. It has a sturdy, lightweight alloy construction. The trailer hitch has a maximum gross trailer weight up to 2,000 pounds and has a maximum tongue weight...
view full answer... - Recommended Trailer Hitch For A 2016 Mazda 3 SedanI can definitely help set you up. You are correct in that the fitment is different for the sedan and hatchback models. For your 2016 Mazda 3 sedan I recommend the Draw Tite Class 1 # 24912. I prefer this hitch over the others we offer mainly because it will be the easiest to install. The other hitches require trimming of the bumper fascia, while the # 24912 will not. This is a standard class 1 hitch rated for towing up to 2,000 lbs. So as long as your trailer and motorcycle weigh 2,000...
view full answer... - Recommended Trailer Wiring Harness for 2018 Mazda 3 with LED Lights For your 2018 Mazda 3 Sedan with LED lights, I recommend the Tekonsha T-One Vehicle Wiring Harness # 118405. This custom harness is confirmed to fit your vehicle and will install by connecting directly to existing ports located behind the driver and passenger side tail lights (inside the trunk). Once these connections are made, you will just need to run the hot lead up to the Mazda's battery. This will provide you with a 4-Way connector to connect with and power a trailer's basic signal...
view full answer... - Which Draw-Tite Class II Trailer Hitch Will Fit On a 2007 Toyota Camry SE V6Yes, the Draw-Tite Trailer Hitch, # 36416, will fit your 2007 Toyota Camry SE V6. Installation of this hitch requires drilling and temporary lowering of the exhaust. But if you have the necessary tools and a helping set of hands, you should be able to install the hitch yourself. I have included a link to the installation instructions and a link to a video showing a typical installation for you to view. If you are planning to do some towing, the recommended ball mount is # 36071 and you...
view full answer... - Largest Trailer Hitch Receiver For 2010 Mazda CX-7A 4 inch trailer hitch receiver is not available for a 2010 Mazda CX-7, or for any vehicle that I am aware of. The largest hitch that fits a '10 CX-7 has a 2 inch receiver: - Draw-Tite Max-Frame Trailer Hitch Receiver # 75512 This hitch is a custom fit for your CX-7, does not require drilling to install, and has a 3,500 lb towing capacity. If you are using it for towing and need a trailer wiring harness, the correct fit for your 2010 CX-7 is the T-One Vehicle Wiring Harness with 4-Pole...
view full answer... - Can Brown Wire on Curt 2014 Mazda 3 Trailer Wiring Bypass the Module BoxHey Dave, thanks for reaching out! The box on your Curt T-Connector Vehicle Wiring Harness # C55567 actually combines the brake light circuit with the turn signals to match the normal 4-Way wiring on a trailer, and it helps to protect your vehicle wiring from anything that might happen with the trailer wiring. This model of wiring has the older Curt module so I recommend replacing your current wiring with the Tekonsha T-One Vehicle Wiring Harness # 118405 on your 2014 Mazda 3 because...
view full answer... - Parts Needed To Install Redarc Trailer Brake Controller On a 2010 Toyota FJ Cruiser No Tow PackageFirst you will need to add a T-One Vehicle Wiring Harness # 118405 to your 2010 Toyota FJ Cruiser. This will take care of the lighting for your trailer connection. The Universal Installation Kit for Trailer Brake Controller # ETBC7 will connect to the 4-way and give you the 7-way connector and additional additional wiring you need for installing a brake controller. The Redarc Tow-Pro Elite Trailer Brake Controller # RED44FR will come with the universal wiring harness needed to connect...
view full answer... - Brake Controller And Wiring Harness Recommendation For 2007 Toyota FJ CruiserThe brake controller I recommend for your 2007 Toyota FJ Cruiser, is the Tekonsha Prodigy P2, part # 90885. This is one of our most popular brake controllers because it is easy to install and use. You said your Cruiser was equipped with a factory tow package. This can have several different meanings, depending on the vehicle manufacturer. Some vehicles come with the 7-way harness, some have a 4-way harness, and some vehicles with the tow package have the drive train or transmission upgraded...
view full answer... - Parts Needed to Tow Motorcycle Trailer with 2016 Mazda 3Motorcycle carriers are seemingly really convenient but the problem with them is that they require the vehicle to have a higher towing capacities due to the weight of the motorcycle and carriers. Typically it has to be a truck or a larger SUV to have the needed capacity. So with that in mind only option for you with your 2016 Mazda 3 will be to tow a small trailer. For that the EcoHitch part # 306-X7305 is a confirmed fit and would be a great choice with plenty of towing capacity. Then...
view full answer... - Which Draw Tite Hitch Fits 2019 Mazda 3 HatchbackThe Curt hitch # C98BR fits the 2019 Mazda 3 hatchbacks like yours. I double checked with them to confirm this just now. The hitch you referenced only fits the sedans. If you were looking to do some towing, we have the trailer wiring kit part # 118405 which is a confirmed fit. This will install very easily and comes with a very reliable converter box as well. For a ball mount you'd need the part # 3593 and then for hitch balls # 19258 for a 2 inch ball or part # 19256 for a 1-7/8 inch...
view full answer... - Adding a 7-Way Trailer Connector and Brake Controller to a 2007 Toyota FJ CruiserTo add a 7-Way trailer connector and brake controller to your 2007 Toyota FJ Cruiser there are a few parts you will need. First, if the FJ does not have any sort of trailer connector already you will start by adding a 4-Way flat connector, # 118405. If it already has a 4-Way skip to the next paragraph. Once the 4-Way is installed you will then need # ETBC7 to add the 7-Way and wiring/accessories to make the 7-Way active and install a brake controller. I have included some links that show...
view full answer... - Is the Module Only on The Curt 4-Way # C55567 For 2016 Toyota Corolla Replaceable? Unfortunately Kurt, Curt does not offer a replacement module for the 4-Way # C55567. I have found the Tekonsha # 118405 option to be more reliable and have less issues over time. So you might consider it when you have to replace the damaged module.
view full answer... - Recommended 4-Way Wiring Harness Converter For 2013 Toyota Camry and Trailer Circuit TroubleshootingI recommend changing to the Tekonsha T-One Vehicle Wiring Harness # 118405 on your 2013 Toyota Camry Hybrid. In my experience the Tekonsha harness has proven to be a more reputable convertor for vehicles. In speaking to one of our technicians who installs these devices on a regular basis, the most important part of the installation is securing the wiring and converter so that the wires do not pull out of the converter box. Tekonsha understands this by giving you a mounting hole in the converter...
view full answer... - Availability of 4-Way Tester and Connector CoverWe do have 4-way testers that would plug into the car side of trailer wiring with the part # I26. This has lights that will come on when it detects that a circuit is active. We have the dust cover part # C58200 which is a fit for both the trailer and vehicle side 4-ways of a vehicle. This would work well for you. I attached a help article on troubleshooting trailer wiring for you to check out too.
view full answer... - Trailer Wiring Fit Recommendation for 2017 Toyota CamryFor trailer wiring confirmed as a fit for your 2017 Toyota Camry you would want the Tekonsha kit part # 118405. We do carry this and it will work well.
view full answer... - Will A Hitch Void the Warranty Of My 2018 Mazda 3 Grand Touring and Which Hitch is Recommended The act of installing a hitch on the 2018 Mazda 3 Grand Touring will not void the warranty because you are covered under the Magnuson–Moss warranty act which prohibits manufacturers from voiding a warranty for adding aftermarket parts unless that after market part caused damage the vehicle. With that said, if Mazda does not recommend towing anything with the Mazda 3 Grand Touring (more than likely they mention it in the owners manual) if towing damages the transmission or any other mechanical...
view full answer... - Recommended Ball Mount for Draw-Tite Class II Hitch 36540 on 2012 Toyota CamryWhen installed on your 2012 Camry, the receiver of the Draw-Tite # 36540 isn't recessed very far under the vehicle so the Draw-Tite # 36071 ball mount will work perfectly in the rise position. The hitch pin is also included. For a trailer ball, use # 19256 for a 1-7/8 or # 19258 for a 2 inch trailer ball. For a trailer wiring harness, I'd recommend the # 118405 from Tekonsha. To see install videos for the # 36071 hitch and the wiring harness I recommended, click the provided links.
view full answer... - Will The Curt Trailer Hitch Receiver For a 2015 Toyota Camry Fit Both Gas and Hybrid Models? The Curt Trailer Hitch Receiver # C12107 which fits the 2015 Toyota Camry will also fit a 2015 Toyota Camry Hybrid. The T-One Vehicle Wiring Harness # 118405 can also be used on both the gas and hybrid versions of the Camry if you are needing a 4-way as well.
view full answer... - Amperage of Fuse for 118405 T-One Wiring Harness The fuse that comes with the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118405 uses a 10 amp fuse. It's probably a good idea to bring the fuse holder along with you to make sure you can find a match when getting a spare. I have added links to a couple install videos as well as the instructions of Trailer Connector # 118405 for you to check out. I also highly recommend using Dielectric Grease for Electrical Connectors # 11755 to help prevent any type of corrosion...
view full answer... - Best Way to Add 7-Way Connector on 2009 Toyota FJ Cruiser for 12V Power to TrailerThe best solution for your application is to install the Tekonsha T-One # 118405 on your 2009 Toyota FJ Cruiser for your standard trailer lights and then add the Wiring Kit # ETBC7L which comes with everything you need to convert the 4-Way to a 4-Way/7-Way and add the 12V function. Please note that as power runs along that line there will be some voltage drop which will likely keep your batteries from charging completely. To help remedy this I recommend using the Redarc In-Vehicle BCDC...
view full answer... - Parts Needed To Install a Functioning 7-Way and Brake Controller On a 2014 Toyota FJ CruiserYou will need our Universal Installation Kit # ETBC7 to connect to the 4-way Connector # 118405 on your 2014 Toyota FJ Cruiser. This includes the wiring for running both a charge line and Brake Controller # RED52VR on your FJ. The end connector will have both a 7-way connector and 4-way flat connector so you will not need to have an adapter for smaller trailers.
view full answer... - Lighting Solution for 2008 Camry Whose Tail Lights Are Blocked by Hitch Bike Rack and BikesYou are wise to consider this safety concern of your tail lights being blocked by your loaded hitch bike carrier. And we can give you an easy solution. A set of magnetic towing lights, such as the cost-effective Optronics # TL21RK, is an ideal solution since these are easy to install and store, and because they can be positioned on any metal surface that gives other motorists a good visual signal that you are braking. Their magnetic base holds them in place. Other options can be seen on...
view full answer... - Is Trimming of Lower Fascia of 2016 Toyota Camry Required for Hitch InstallTo install a hitch on your 2016 Toyota Camry you will be required to remove or trim the underbody panel as well as modify the heat shield slightly. I attached an install video that shows everything required to install this hitch on a 2016 Camry like yours. For a ball mount you would want the part # 36071 and the ball # 19256 for a 1-7/8 inch ball. For trailer wiring you would then want the # 118405.
view full answer... - Which Trailer Wiring Harness is Recommended for a 2015 Toyota CorollaFor your 2015 Toyota Corolla the Tow Ready Harness part # 118405 that you referenced is a confirmed fit and would work well. I attached an install video for you to check out as well. For a trailer hitch you would want the part # 24913 then as well. For a ball mount you would want the part # 3593. For a ball part # 19256 for a 1-7/8 inch ball and # 19258 for a 2 inch ball.
view full answer...
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
Test Fit:
Joe V
Test Fit:
Alan C
Test Fit:
Randy B
Test Fit:
Shane H
Test Fit:
Ryan G
Expert Research:
Mike L
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Jeffrey L
Video Edited:
Zack K
Video Edited:
Joshua S
Video Edited:
Jacob T
Video Edited:
Dustin K
Video Edited:
Sue W
Video Edited:
Chris R
Video by:
Andrew K
Video by:
Kathleen M
Video by:
Jonathan Y
Updated by:
Adele M
Updated by:
Laura H
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Isabelle B
Installed by:
Cole B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
James
11/26/2023
Ive had this installed for a year with no issues. Works perfectly!