To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your Kia Sorento with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side tail lights. You will have to remove the tail light assemblies to access this harness. Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. This converter is a circuit-protected, battery-powered unit that bypasses the electrical routes that are used by a basic wiring harness. As a result, there is virtually no draw on your tail light circuits.
Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of the trailer. This converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
California residents: click here
Average Customer Rating: 4.7 out of 5 stars (219 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.
Wiring harness has quit working less than a year after purchase, one trailer brake light is always on, neither of the turn signals or the other brake light is still working.
I finally got it installed everything works great and the instructions and pictures were a big help .the items arrived on time as you indicated and the customer service was great thank you .
Easy to install, I like how it isolates the electrical system and it works great. Your video instructions were outstanding. With the video a five year old could install the wiring. This was installed in my 2019 Kia Sorento. The first pix shows in the back very low profile, the second pix shows inside the engine compartment, truly cool.
Mr M.
3/5/2021
Ive had no issues at all. Works great. I did bottom-out once but it was my fault, deep ravine. The hitch seems to stabilize my rear end somewhat. Dont know if its good or bad. Forgot to mention, your wiring harness is super cool and easy to install.
My husband said it works great. The only issue was he had to run a wire from the back of the vehicle to the front to the battery. But, that is just because of the vehicle we have no fault of etrailer.
Mrsp
10/9/2023
So far the replacement is working well. We had to replace the first one because something shorted out the control module. E-trailer customer service was excellent with helping us with the return and sending us the new part.
Mike L.
10/25/2023
This is the second trailer wiring harness that I have installed on a Kia Sorento. The first was on my 2012 Sorento. This one is on my 2014 Sorento. Having used the online video installation instructions the first time around and having no problems, I went straight to the video for my 2014 Sorento. The Curt T-Connector kit makes wiring easy. No splicing, just plug in the matching connectors, mount the power converter and run a few wires for a ground and forward to your battery. Hiding the wires behind the hitch as per the instructions with cable ties gives a clean look. I also mounted a Curt plug receptacle to the hitch so that the connector is not just hanging on the safety chain holes. As you can see from the photo I believe this gives a clean , professional look.
The real deal. Don't waste time and money with other companies. Order what you need from here and you know it will be right.
William
2/12/2024
Still going strong.I still highly recommend this type of product. You can save so much doing it yourself if you are physically comfortable doing the work.And if you need more information on installing a product just call for the assistance. Great company to deal with.
Mike L.
2/12/2024
The trailer receiver was an easy installation, installing the wiring kit in a Kia Sorento was a pain.
We have been using the package for one year with no problems. Yes, I would order from Etrailer again.
My order was shipped promptly and arrived in good condition it was excactly as described.
This wiring harness fit as it should on my 2021 jeep wrangler 4xe. I am quit happy with the results. There is only one item would change and it is the metal bracket that holds the 4 wire plug. It doesn't have a great design.
I had this installed by a mechanic. The installation is difficult if you don't have a lift and all the tools. However, once installed, the product works great. I highly recommend this product.
"first impression was that this harness is pretty high quality and seems complete. as i worked with it, using the directions as needed, i felt it was easy to follow and accurate. i followed exactly what was explained for the 2 tail lights. they went somewhat smoothly, the only exception being getting them off the car. i ended up referring to several videos to get them out. what finally worked was using packaging tape attached to the long outside portion of the lens. pulling this and wedging my fingers just inside the black plastic edges on the inside. after quite a few pulls, each came loose. be sure sure to use your body as a stop, to keep the light assemblies from jerking out too far from the body, lest you break plastic or the wire connector.
for the ground and the power wires, i did things differently. basically i spliced a much longer ground wire to what was there and ran it together with the extra length of hot wire (black wire). my car has a 12V 180W cigarette type plug-in near the back on the passenger side. i opted to route the ground/hot wires behind the panels up near this cigarette plug. i cut a small hole in the bottom of the passenger light assembly plastic access panel, and routed the ground/hot wires out here nearly next to the cigarette plug. i ended up buying a fused cigarette plug and connected the ground/hot wires to it, then plugged it in. it might be nice to include a cigarette plug in the kit as i suspect all sorentos have this rear 180w outlet.
lastly, i routed the 4-pin connector wires differently too. i did not want this plug just hanging out the back of the car when in use. so, with the spare tire out of the way anyway from the hitch installation, i looked for a body plug there. i gounf 2 metal plugs about 3/4" in diameter and removed the one closest to the driver rear light assembly. i enlarged it to just barely allow the 4-pin connector to pass through (1.5" x .75"). the 4-pin connector wire are then routed and secured out of the way of the spare tire, the hitch and comes out from below the rear bumper facia besides the hitch. my trailer has a 7 blade round connector, so i needed an adapter to the 4-pin connector.
finally, the control unit is anchored with the supplied 2-sided tape below and to the right of the driver access panel. there is a flat area there that hold it securely.
... and now all camper trailer lights work as intended, night lights, brake lights, turn signals. i've attached some pics to hopefully help with the above explanation."
The products were exactly as described and the delivery was in two days instead of the advertised five ! I have shopped at eTrailer.com before and I will certainly do so again. Excellent company to do business with.
Couldn’t be happier! This was such a better experience than Amazon. I ordered one from Amazon originally, it took forever to arrive, and it didn’t fit. So I came here to etrailer the price was comparable, the quality is better, they shipped it faster(I payed for the 2 day shipping), it was easy to order, the online instructions for installation on YouTube were great. Next time I’m coming straight here.
Right part and on time.. good price
Patrick
12/2/2023
It has worked well, used it many times. Easy to install.
Awesome. Was a simple hookup everything was as described
Great, shipping was fast and came with everything we needed.
fit and finish were very nice, installation instructions spot on, would purchase again if needed
Excellent service, unbelievably fast shipping! Highly recommend etrailer for your needs!
The second install - a "Upgraded" system worked great. It was a plug 'n play so I didn't have to splice, solder and tape wires. Your video and printed instructions were very clear and spot on. Screwed the flat 4-pole mounting bracket to the hitch frame and used JB Weld to bond the flat connector to the mounting bracket.
thanx,
bill
Bill A.
8/16/2018
trouble free, no problems
Connector works great.
Extremely helpful video on etrailer website convenienced me to purchase this wiring harness for my 2018 Kia Sorento. Every bit as easy as pie! A well engineered harness with plenty of length on the wiring and all the plugs matched. You may need additional black zip ties on hand if you’re picky like me.
Jim H.
4/28/2019
Installed it a year ago. Everything still works perfectly! Be sure to watch the video before you begin installation and you will be just fine!
Nicole T was a great saver of Get to g my vehicle ready to pull my trailer. The wiring harness I purchased thru a different supplier failed to ask a crucial vehicle option. It caused the wrong wiring harness to be purchased. I contacted Curt directly and Nicole T was on the job with her "A" game. She asked the right questions, allowing me to select the correct wiring harness. She arranged shipping to ensure I receive it as early as possible, the next day. Installation was quick & easy. Thank you Nicole T.
Pat A.
8/22/2019
Great, it has lived up to my expectations. Again, without Nicole T knowledge of your products & ability to ask the required information, I would have had to postpone my trip & spend additional money. Thank you again Nicole T & Curt.
Install was smooth and easy to follow instructions took about an hour to complete
The harness connector c56256 not working properly. After installing trailer hitch looked good but the harness c56256 has problem, checked light left signal work brake light work but right signal not working.
I need to call or need nice replacement c56256 harness connector.
Sierra K.
1/24/2022
Customer Service will reach out to you.
Simple to install only thing I didn't use that was sent was the butt connectors. Personally don't like that style . Small issue with preference is all. Looks like it was factory done and not after like other wireing harness that I have seen or used.
Roger B.
2/19/2019
Have had one issue with it in a year. My right rear marker light will stay on if I leave the in line fuse in when no trailer is connected. Simple enough fix I dont pull a trailer that much so I just pull the fuse when Im not using it. Not sure if its auto manufacturer issue or trailer wiring issue but eh not that hard to overcome
Rachael H.
2/20/2019
Package contained everything promised in first class quality and instructions. Fit at all points was perfect and easy to install. Supplied instructions were clear and specific. I have experienced no adverse issues with the installed wiring. Highly recommend this wiring kit. My installation was on a 2016 Kia Sorento SUV.
Milt F.
3/21/2019
After one year the unit is still functioning perfectly. Quality product all the way.
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jenny N.
2/7/2024
It sounds like the harness has shorted out. To do a bit of trouble shooting, start by using a circuit tester to check the functions at the 4 flat connector. Also check the ground wire remains as a good solid ground to bare metal. You can then next check the signal of the wires leading into the converter box and out of the converter box. If you have a signal entering in the box and not out the other side then the harness will need to be replaced. I have a FAQ below that can help with testing the harness.
Helpful Links
faq-4-5-way-troubleshooting.aspx