Does Curt Wiring Harness 56256 Fit 2019 Kia Sorento Without Factory Tow Package

Question

Question:

Will the curt trailer wiring harness #C56256 fit my 2019 Kia sorento L 2.4 li without factory tow package?

asked by: Robert H

0

Expert Reply:

Yes it will! The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56256 is a fit for your 2019 Kia Sorento that does not have the factory tow package.

That said, I do highly recommend the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118583 instead because we have found these to be the most reliable wiring harnesses.

I have added links to video installs of both wiring harnesses for you to check out. Additionally, if you need to complete your towing set up and need a hitch for your 2019 Kia Sorento I recommend the etrailer Trailer Hitch Receiver # e98843.

expert reply by: Kyle S

0

Answer 1

Yes, the Curt trailer wiring harness part #C56256 that you referenced does fit your 2019 Kia Sorento without the trailer towing package.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

If your 2020 Kia Sorento has the factory tow package, there will be a tail light wiring connector behind the rear tire of the driver side, on the outside of the frame rail. As shown in the attached photos, an underbody cover will need to be removed…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

The EcoHitch Hidden Trailer Hitch Receiver #EH35VR may interfere with the Hands-free Liftgate sensor like all of the other hitches. Typically this means you will need to place your foot on either side of the receiver tube in order to activate the…

view full answer...