4-1/8" x 1-1/4" Rectangle. Waterproof, incandescent trailer light functions as both a clearance light and a side marker light. Premium bulbs for long life. Surface mounts with included bracket and lead wire. PC rated. 2 Bulbs.
Features:
Specs:
Manufacturer Cross Reference
Light will work as an exact replacement for:
Optronics # MC67RBP
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The circuit board is sealed, which means that water will not damage the diodes or circuit board.
A PC-rated light produces a 90-degree angle of light to either side of its centerline for a total of 180 degrees of coverage. This beam pattern can be clearly seen when you are standing directly in front of the light, as well as when you are standing on either side of the light. When properly installed, this type of light can function as both a front clearance light and a side marker light or as a rear clearance light and side marker light.
Surface mount lights install flat against the surface of the trailer, so a hole does not need to be cut into the trailer for the light. This type of light is installed using a flange or bracket that has mounting holes. And mounting hardware is used to secure the light to the trailer.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we'll be taking a look at the Peterson Clearance and Side Marker Trailer Light Kit. This is going to include your light and the mounting bracket to get this installed. That mounting bracket provides us with a housing for our light and then it also has our ground connection there and the wiring coming off of it so we can get everything hooked up and lit. This is compatible with 12 volt DC systems. It has bulbs that are incandescent, but it is a sealed waterproof housing and lens unit, so it is submersible. You can use this on your boat trailers and it'll still stay lit without it getting any damage from the water.
Also just makes an overall long lasting light so there's no dirt or debris you can get in there either.We'll have two incandescent bulbs in there. We'll go ahead and hook this up to my power source so you get an idea of how bright that will be. When I hook my power to the one wire coming off of it and then my ground to that little terminal there, that little ring. Turn on my power, you'll see our light will come on. This is a PC rated light, so that means that it's visible both when you're looking straight at it and from the side so it can be used as a side marker and a clearance light at the same time, so you only need one light to do that function for you if it's mounted properly, that is.
So this is just a surface mount to the trailer. It does not come with any hardware to mount this, so you will have to pick some up on your own and you can remove this from the housing.These two tabs on either side, if you get a flat bladed screwdriver and kind of pry out on that, it'll free up the tab on the light and then you can separate the light from the housing. That will allow you to then mount it up with some screws or some hardware. Again, that is sold separately. This is DOT compliant.
Again, PC rated. Dimensions for the light on its own, it's about three and seven eighths inches long to the end of the tabs. The bracket overall is just over four inches at about four and an eighth inches there. The width of the light is a little bit more than the bracket and that's about one and an eighth. And then our bracket is just about one inch deep or one eighth inch thick there.
Overall height of just the light is about an inch and an eighth. And then with the bracket in place, it's a little bit taller. It's about an inch and five eighths so just over a half inch, an inch and a half. The distance between our two mounting holes, center to center is about three inches.Our wiring coming off of the bracket is about five inches long. It does have a one year limited warranty from Peterson, and that's going to do it for our look at the Peterson Clearance Side Marker Trailer Light.
Average Customer Rating: 5.0 out of 5 stars (4 Customer Reviews)
4-1/8" x 1-1/4" Rectangle. Waterproof, incandescent trailer light functions as both a clearance light and a side marker light. Premium bulbs for long life. Surface mounts with included bracket and lead wire. PC rated. 2 Bulbs.Good quality part and shipped fast
OEM quality!
Just what I needed! Thanks!
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.