4" x 1-1/2" Rectangle. LED trailer light functions as clearance or side marker light when properly mounted. Built-in reflex reflector. Durable ABS housing. Snap-in lens. Surface mount to trailer. 2-Wire with 0.180 bullets. P2 Rated.
Features:
Specs:
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
Surface-mount trailer lights install using a flange or bracket with mounting holes. These lights lay flat against the trailer surface and only require a small, often pre-existing hole, for wiring. Mounting hardware is used to secure the light to the trailer.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're gonna take a look at the Optronics LED Clearance or Side Marker Light with Reflector. This is going to be an LED light to keep you in compliance with all the rules of the road, and also keep you safe. It will replace, or upgrade any of your existing trailer lights.The nice thing about this is that since it's an LED, we don't have to worry about any maintenance with this. There's no bulbs that can go bad on us that we have to open up the housing, get in there and change out the bulbs, find them first of all, and then replace them. Pretty much as soon as we have this installed, it's good to go. We won't really need to replace it unless something happens where the lens itself gets damaged.It has that built in reflector, so that even when the lights aren't on our trailer will still be visible by reflecting that light.
It's gonna have a two pigtail design, or two wire pigtail design. These are going to have 0.180 male bullet ends. You just have to connect these up to power and ground. White will be ground. Black will be power.
Flip that on. You can see our two diodes come on there. Turn off the lights in the studio, and you get a better idea of how bright that is. It's not really to provide lighting, per se. It's just to make our trailer visible in the dark.Now, this is going to be P2 rated, and basically that means that our light is going to be visible up to 90 degrees, but once we get to 180 degrees it's not really visible anymore.
That's why you need to use this as a clearance, or a side market light. That's what gives it that P2 designation.The housing is gonna be made of a durable ABS plastic with an acrylic lens, so it will be durable enough to have out on the road. This is going to be compatible with 12 volt DC systems. Our lens is going to be a snap on design. You pop that off.
If you do need to adjust the wires, as you can see my black wire is a little bit shorter, so I can pull that through and give myself a little bit more wire there, and get it out of the way of the hardware.But, that's also how we would mount the hardware up in the first place. We would be able to mount it in place. It doesn't come with the hardware, so you will have to provide that on your own. But once it's mounted, just snap the lens back over it, and it's ready to go. That keeps the light nice. It keeps out most of the dirt from getting in there.As far as dimensions, the light is about 4" long by about an 1 1/2" wide, and so it'll be just about an 1" thick. The distance between our mounting holes center to center is 3". Again, this is going to have two diodes. Our wiring, as you can see, it's a little bit off. Our black wire is a little bit shorter, but the white wire is about 9" long. With the slack that I have pulled out for my black wire, it's about 7 1/2".This is going to have a power draw of 0.04 amps at 12.8 volts. There is a limited lifetime warranty on the LEDs from Optronics.That's gonna do it for our look at the Optronics LED Clearance or Side Marker Light with Reflector.
Average Customer Rating: 4.7 out of 5 stars (15 Customer Reviews)
4" x 1-1/2" Rectangle. LED trailer light functions as clearance or side marker light when properly mounted. Built-in reflex reflector. Durable ABS housing. Snap-in lens. Surface mount to trailer. 2-Wire with 0.180 bullets. P2 Rated.Direct Replacement
They were a great and easy replacement light.
Item as described. Quick delivery
still works great
Was the light that I needed. Installed and working.
Exactly what we needed and quick delive ry.
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.