Dexter Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles - 6 on 5-1/2 - Pre-Greased

See what our Experts say about this Dexter Trailer Hubs and Drums

• Could Studs of Dexter 3,500 lb Trailer Hub Be Removed
  We only have the Dexter Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles # 84655UC1-EZ available with 1/2 inch wheel studs but you could remove the studs and install the size you are wanting.
  view full answer...
• Where to Measure to Pick Out Replacement Hubs for a Trailer
  We can definitely help! Using your micrometer get the dimensions of where the bearings and the grease seal ride and we can set you up with a hub that fits (if available). Check out the picture I attached for more information on where to measure.
  view full answer...
  
• Correct Non-Braking Idler Hub Replacement for Dexter 8-250 Trailer Hub
  The Dexter Trailer Idler Hub Assembly part # 84655UC1-EZ is the correct idler hub replacement for a Dexter 8-250 Hub. It uses the same L68149 and L44649 bearings and has a 6 on 5-1/2" bolt pattern.
  view full answer...
• How To Use Toyota TRD Pro 17 Inch Wheels With Hubs On a Dexter 3,500 Lb Axle
  The wheel bore can be an issue but the bigger concern I see right off the bat is that you have 5 lug hubs and want to use 6 lug wheels. Therefore, we need to get you the correct hubs first before you can address the hub bore difference. The good news however is that you can upgrade to 6 on 5-1/2" bolt pattern with the Dexter Trailer Idler Hub Assembly part # 84655UC1-EZ. According to my research, the Toyota TRD Pro 17" Wheels have a 6 x 139.7mm bolt pattern which is the same as 6 on 5-1/2"...
  view full answer...
  
• Replacement Hub Recommendation for a 2000 Shorlander Model SD v 1831
  I pulled up the manual from your boat trailer and was able to find out that your trailer has an 84 spindle on it which means we have a hub that will fit. For an idler hub that would fit your hub that has a 5 on 4-1/2 inch wheel bolt pattern you would want the Dexter Hub part # 84545UC1-EZ. If you have a 6 on 5-1/2 inch bolt pattern you would want the Trailer Hub Assembly part # 84655UC1-EZ. If you are unsure of what bolt pattern you have check out the FAQ article I attached determining...
  view full answer...
• Compatibility Of 3500 lb EZ Lube Spindles And Dexter Hub Assemblies
  The #84 EZ Lube Spindle # TRU74FR is compatible with hub assemblies # 84655UC1, however I recommend you use the Trailer Hub Assembly - 3,500-lb Axles - 6 on 5-1/2 - E-Z Lube # 84655UC1-EZ instead for easier access to your EZ Lube Spindle.
  view full answer...
• Idler Hub Recommendation for a Trailer that has # 84 Spindles
  Based on the inner diameters of the bearing you gave it looks like you have a number 84 spindle. For an idler hub that would fit your hub that has a 5 on 4-1/2 inch wheel bolt pattern you would want the Dexter Hub part # 84545UC1-EZ. If you have a 6 on 5-1/2 inch bolt pattern you would want the Trailer Hub Assembly part # 84655UC1-EZ. If you are unsure of what bolt pattern you have check out the FAQ article I attached determining bolt patterns.
  view full answer...
• Replacement Hub Recommendation for a Hub that Uses L44610 Outer and L68111 Inner Races
  Actually the numbers you listed are races and not bearings, but nevertheless I was able to determine what you need. Also, it sounds like you meant to type 6 on 5-1/2 inch bolt pattern. For an idler hub you would want the part # 84655UC1-EZ. For a hub and drum you would want the part # 84656UC3-EZ.
  view full answer...
• Timbren Axle-Less Suspension Compatible with Hubs That Have 6 on 5-1/2 Inch Bolt Pattern
  In order to use the # 84655UC1-EZ hub with the desired 6 on 5-1/2 bolt pattern, you'd need to use a Timbren Axle-Less suspension that has spindles compatible with a L68149 inner/L44649 outer wheel bearing like # ASR1THDS02. The hubs have a 3500 lb capacity, but the capacity will be limited by the 2200 lb capacity of the Timbren suspension.
  view full answer...
• Can a Trailer Axle be Put On a Truck Bed to Make a Trailer
  First, I am pretty sure you don't have to change the axle out if you are making a trailer out of a truck bed. You will want to check the laws in your state/area though. The highest capacity straight axles that we carry are rated for 3,500 pounds which likely exceeds the capacity of the truck bed. For a trailer axle that will accept a hub with a 6 on 5-1/2 bolt pattern you could use # T3584F-8974 with hub # 84655UC1. Or EZ lube axle # T3584F-EZ-8974 with hub # 84655UC1-EZ. Both of these...
  view full answer...
• Parts Needed to Upgrade a Utility Trailer to 2k Axles
  While we do not have an option for you, we do not carry any 2k axles that have the 64" hub face to hub face measurement you need. The only option would to be to purchase an axle-less system like the Timbren Axle-Less Trailer Suspension System - Regular Tires - 2,000 lbs # ASR2KHDS02. For the hubs, you need the # 84655UC1-EZ. The hubs provide you with a 6 on 5-1/2 lug pattern to use your current wheels. I went ahead and attached some helpful videos for you to check out.
  view full answer...
• Compatible 6 Lug on 5-1/2 Inch Bolt Pattern Idler Hub and Total Drop of Timbren Axle-Less Suspension
  We do have an idler hub with a 6 lug on 5-1/2 inch bolt circle that's compatible with the Timbren # ASR2KHDS03 Axle-less suspension, the part number of the hub is # 84655UC1-EZ, they are sold individually. The drop of the spindle, measured from the underside of the trailer frame to the center of the spindle is 7-1/2 inches. This includes the lift plus the spindle drop. I've provided you with a diagram we received from Timbren that shows all the relevant dimensions for you.
  view full answer...
  
• Do Dexter 3,500 lb Axles Use Hubs With L68149 and L44649 Bearings
  Thanks for the kind words, it's nice to hear! Also, it is extremely likely that your Dexter 3,500 lb axle is going to have inner bearing # L68149 and outer bearing # L44649 which will allow you to use the Dexter Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles - 6 on 5-1/2 # 84655UC1-EZ you referenced. For reference, every single one of the Dexter hubs we carry for 3,500 lb axles use those same bearings so this hub will work for you without issue. I've added a link to a video review...
  view full answer...
• Inner Diameters Of Bearings Included In Dexter Hub Assembly # 84655UC1-EZ
  The inner diameter of the # L68149 bearing measures 1.378 inches. The 1-3/8 measurement you gave is equal to 1.375 inches. The inner diameter of the # L44649 bearing measures 1.063 inches. The 1-1/16 measurement you gave me is equal to 1.062 inches. You can use a digital caliper to measure your spindle to ensure you find the correct size bearing. A digital caliper allows you to measure as exactly as possible. If your inner bearing measures 1.375 instead of 1.378, you will want to use...
  view full answer...
  
• Is Timbren Axle-Less Suspension and Dexter Axle Idler Hub Good for a Small Trailer with Camping Gear
  Combining the Timbren Axle-Less Trailer Suspension System # ASR2000S02 with the Dexter Trailer Idler Hub Assembly # 84655UC1-EZ is a great option for a small trailer and camping. One of the biggest advantages of the Timbren Axle-Less systems is that they increase ground clearance for the trailer since you don't have an axle tube hanging below everything else. If you were only needing the suspension parts for your trailer build then you shouldn't need any other parts to finish your project....
  view full answer...
• Availability of Timbren Axle Less Kit with Lift Kit that Can Have Hub with 6 on 5.5 Bolt Pattern
  For a 4 inch lifted Timbren Axle Less kit that can have 6 on 5-1/2 inch bolt pattern hubs installed on it you'd want the part # ASR35HDS02. Then for a hub with the bolt pattern you need you'd want the # 84655UC1-EZ.
  view full answer...
• Recommended Axle-Less Suspension System For Lightweight Off-Road Trailer
  Since you want to travel off-road I recommend the Timbren Axle-Less System, part # ASR1200S01. This is designed for off-road tires and has a capacity of 1,200-lbs. The hub assembly I recommend is part # 8-91-05UC1-EZ. This system does not have the same bolt pattern as your Tacoma. This hub has a 4 on 4 wheel bolt pattern. Since you said you want to match the 6 x 5-1/2 bolt pattern of your Tacoma you will need to use a more heavy-duty system like part # ASR35HDS01. This is a 3,500-lb...
  view full answer...
• Idler Hub with 6 on 5-1/2 inch Bolt Pattern Recommendation for Timbren System # ASR35HDS02
  I have a solution for you, but the # 84655UC1-EZ will not fit on the spindles of the # ASR35HDS02. For a similar idler hub that is confirmed to fit you would want the # AKIHUB-655-6-K. This is an idler hub with the same bolt pattern that will fit the spindles of the Timbren.
  view full answer...
• Replacement Drop Axle for Old Horse Trailer with 6 on 5-1/2 Inch Bolt Pattern
  I would love to help but we do not have any trailer hubs that correspond to the dimensions that you provided. Therefore, the only option we can offer you would be to replace the axle all together. In order to offer a replacement for this we would need to know your spring center and hub face measurements (see photo). If you can provide me with these I can then see if we have an axle suitable for your trailer. For example, the Dexter Trailer Axle Beam with 4" Drop E-Z Lube Spindle part...
  view full answer...
  
• Idler Hub Compatible With Timbren Axle-Less Suspension System
  I can get you a hub assembly that fits, but the Idler Hub Assembly # 84655UC1-EZ will NOT work with the Timbren Heavy-Duty Axle-Less Trailer Suspension # TASR35HDS06. Instead, you're going to need a hub and drum assembly with this suspension and the correct fit is Hub and Drum Assembly # AKHD-655-6-EZ-K. This assembly is compatible with the Timbren's EZ Lube spindle and uses the correct inner bearing # 25580, outer bearing # 15123 and grease seal # GS-2250DL
  view full answer...
• How to Find Correct Replacement Bearings for 2003 Roadmaster Enclosed Utility Trailer
  It is a good idea to go through your trailer's hubs and bearings to make sure everything is in good shape before your cross-country trip. The easiest way to find the correct replacement bearings, races and seals is to use the part numbers from the original parts that are on the trailer now. Please refer to the linked photo that shows the typical location and appearance of these part numbers. We offer many popular combinations of bearings, races and seals as kits, but the individual parts...
  view full answer...
  

Do you have a question about this Trailer Hubs and Drum?