Compatibility Of 3500 lb EZ Lube Spindles And Dexter Hub Assemblies

Question

Question:

Will these spindles and hubs fit together? 2 TRU74FR - #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter 2 84655UC1 - Trailer Hub Assembly - 3,500-lb Axles - 6 on 5-1/2

asked by: Todd

0

Expert Reply:

The #84 EZ Lube Spindle # TRU74FR is compatible with hub assemblies # 84655UC1, however I recommend you use the Trailer Hub Assembly - 3,500-lb Axles - 6 on 5-1/2 - E-Z Lube # 84655UC1-EZ instead for easier access to your EZ Lube Spindle.

expert reply by: Jason S

0

Answer 1

The #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axles #TRU87FR is not brand specific so it will work with a Dexter axle tube. It will fit 2-3/8 inch diameter axles.

view full answer...

Answer 2

There really isn't a solution we can provide aside from replacing the spindle since yours is damaged beyond repair. Since you have a 3,500 lb EZ lube axle the correct replacement spindle would be the part #TRU74FR. I recommend taking it to a…

view full answer...

Answer 3

Both of the Dexter Trailer Springs Over-Under Conversion Kits, part #K71-384-00 for 2-3/8" axle and part #K71-385-00 for 3" axle, come with installation instructions. As of yet (April 2018) we don't have any installation…

view full answer...

Answer 4

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

Hey Jaime, yes you can replace your 25-1/4 inch 3,500 lb axle leaf springs with a 5k rated axle spring like the part #e44SR. This will increase the suspension's weight capacity and might make the ride quality a little rougher but it would fit…

view full answer...

Answer 7

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are…

view full answer...

Answer 9

The trailer will have a plate or sticker on it that will list the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that will list the weight capacity. You can…

view full answer...

Answer 10

An EZ lube spindle will be better because it allows you to insert grease from inside the spindle where the bearings are and push out the old grease whereas with a Bearing Buddy you basically just get to push grease through the front of the hub. I…

view full answer...

Answer 11

Hey Doug, thanks for reaching out! The MORryde ALLTREK 4000 #MR89DR dimensions can be a bit difficult to explain via text so I've attached an image giving you the dimensions you're asking about!

view full answer...

Compatibility Of 3500 lb EZ Lube Spindles And Dexter Hub Assemblies

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching