Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
(105 reviews)
Price: $295.67
Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
Item # C14082
Retail:$482.95
Our Price: $295.67
You Save: $187.28
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near meIn-stock alternatives that can ship today
- All Info
- Reviews (105)
- Q & A (0)
- Photos
1996 Ford F-250 and F-350 - Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Class IV
- 2 Inch Hitch
- 10000
- Concealed Cross Tube
- 1000
- CURT
- 12000 lbs WD GTW
- 1200 lbs WD TW
- Custom Fit Hitch
This fully welded trailer hitch receiver bolts onto your Ford 's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.
Features:
- Custom fit is designed specifically for your vehicle
- Precision, robotic welding maximizes strength and improves fit
- Bolt-on installation - no welding required
- Complete hardware kit and installation instructions included
- Lifetime technical support from the experts at etrailer.com
- Gloss black powder coat finish over protective base coat offers superior rust resistance
- Sturdy, square-tube design
- Ball mount, pin and clip sold separately
- Hitch assembled in the USA
- Mounting hardware may be imported
Specs:
- Receiver opening: 2" x 2"
- Rating: Class IV
- Maximum gross trailer weight: 10,000 lbs
- Maximum GTW when used with weight distribution: 12,000 lbs
- Maximum tongue weight: 1,000 lbs
- Maximum TW when used with weight distribution: 1,200 lbs
- Maximum gross trailer weight: 10,000 lbs
- Measurement from center of bolt hole to center of bolt hole: 31-1/4"
- Limited lifetime warranty
Note: Your vehicle must have 34" frame spacing
etrailer.com Technical Support
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
14082 CURT Trailer Hitch Receiver - Custom Fit - Class IV - 2"
Installation Details
Weight Carrying Capacity
Gross Towing Weight (GTW):
10,000 lbs.
Tongue Weight (TW):
1,000 lbs.
Weight Distribution Capacity
Gross Towing Weight (GTW):
12,000 lbs.
Tongue Weight (TW):
1,200 lbs.
Gross Towing Weight (GTW):
10,000 lbs.
Tongue Weight (TW):
1,000 lbs.
Weight Distribution Capacity
Gross Towing Weight (GTW):
12,000 lbs.
Tongue Weight (TW):
1,200 lbs.
Tech Tip
Drilling required for installation , Product fits vehicles with frame that is 34" wide outside to outside
Complete Towing Package for 1996 Ford
Retail:$651.57
Package Price:$403.85
1996 Ford F-250 and F-350 Owners Who Purchased This Trailer Hitch Also Bought...
Popular Trailer Hitch Accessories
Customer Satisfaction Score:
89% were satisfied with this product
11% of customers were not satisfied
- Wrong item was ordered
- Did not arrive in time
- etrailer mistake
Customer Reviews
Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2" - C14082
Average Customer Rating: 4.8 out of 5 stars (105 Customer Reviews)
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.by: 05/29/2022
2007 Isuzu N-Series
Installed on 2007 Isuzu NPR chassis with frame extensions for bumper brackets.
This hitch DOES fit. Actual hitch width is 33.75 inches so it fit perfectly between the bumper bracket extensions. Slid in Like buttah.
Hardware length allowed for avoiding a bolt head protruding from the frame and installing double shims from underside. Very helpful.
5.5 inch drop put receiver below the bumper. Thank you etrailer for pictured measurements.
by: Chris 04/13/2024
Hitch was falling out of the box when delivered. But will do its purpose. Fast shipping
by: Kismetsdad01/02/2024
1985 Chevrolet C/K Series Pickup
There are only so many ways to describe a trailer hitch.
by: Timothy06/10/2021
Hitch fit good on a 74 Ford super camper special. There we two rivets on the frame for a crossmember that I ground down and drilled out because they were exactly where I wanted the front mounting hole on the hitch to be located. Other than that pretty good.
by: Ronald P.08/17/2016
1987 GMC C/K Series Pickup
We put this hitch on my 1987 GMC 61/2' short box 4WD with a regular bumper with no problems and look real nice and real strong with good load ratings
Ronald P.
8/29/2017
real good havent pulled anything yet
by: Mike Goswick05/04/2024
1997 Chevrolet C/K Series Pickup
The hitch is to short width wise - will not fit my truck
by: Ron W07/08/2017
Chevrolet
bought two of these receiver hitches, one for my 1987 GMC V1500 SWB and one for my 1984 Chevrolet K10 SWB. both went on perfectly and look great. Haven't pulled anything yet
by: Shawn08/24/2023
1983 Chevrolet C/K Series Pickup
It came all scuffed up and with a bent mounting arm...
How do you bend a class 4 hitch...??
by: Eric 09/16/2023
Have not put the hitch thru any hauling duties, it was easy to install, l completed the install by myself.
by: Ryan09/01/2023
1998 International Trucks 3800 Series
Bought a 1998 international 3800 (school bus) fit is pretty good, product is superb! Packaging could be better.. had some scuffs and scratches.
by: Toni-Ann10/03/2023
Nice heavy duty hitch great for my school bus good product I would go again
by: Scott 08/16/2023
This was delivered extremely fast! Made it here in one piece! Can’t wait to install it. Another great products from Etrailer! Thank you guys again. Will be back soon!!
by: Jens 12/06/2023
Excellent quality, but unfortunately didnt fit, send it back and ordered correct one.
Great costumor service.
by: Jack 02/04/2023
This makes my 4th Curt hitch purchased from etrailer. 5th overall and they have all performed flawless. I pull a trailer probably 5 out of every 7 days. Always have excellent customer service from etrailer and recommend them to anyone needing a hitch.
by: Erik 12/30/2023
Hannah was correct and punctual with her Customer Service!!!!!!! Keep up the good work!
by: Jerry C02/02/2014
I purchased a used ambulance as a work vehicle for my company. Needed a hitch but not sure which one I would need because of the ambulance box. One phone call to etrailer with their friendly operator and a referral number to tech support and I had my answer. A couple of quick measurements and I had my hitch product number. Placed my order online on a Monday, hitch arrived on Wednesday. Drilled the required holes in my vehicle
and I was in business. Fantastic service! Between friends an family we have ordered at least 6 hitches and accessories over the last several years.
Lewis R.
2/22/2014
What are the measurements and demensions of this hitch? I understand that all of the Chevy GMC 1/2 and 3/4 ton pickup frames are the same between 1967 and 1972. My truck is a 1969 C/10 long bed with the coil spring suspension. Will this hitch bolt up onto my frame without having to modify either the frame or hitch?
by: Curtis 11/30/2023
good piece,,,did excellent on shipping fast!!
by: Raymond 09/21/2023
1970 Chevrolet C/K Series Pickup
Shipping was very fast,customer service excellent, product looks excellent as far as welds...if it wasnt for the numerous scratches,scrapes,etc. would have given 5 stars.
by: Dan07/22/2023
Hitch is beautiful, I give it 6 stars.
I didn't expect to have to drill holes in the frame to attach it. (subtract 2, for extra work)
by: Ramiro C08/26/2023
1987 Chevrolet C/K Series Pickup
It’s perfect, you can barely see it, very beefy
by: Don07/31/2017
1964 Chevrolet C/K Series Pickup
Have not used the trailer hitch, only installed as it was one of the early steps in the frame off restoration of my 1964 Chevy truck. It was a bit more work than the videos suggest. After ordering a second hitch that was to fit my truck, I still had to do substantial drilling. Not one hole really lined up. But it sure looks secure and substancial now! Look forward to having a bit more confidence in my hitch while towing.
by: Rick09/14/2022
Talk to the guy about the Curt hitch that went bad and he was very rude, arrogant, and didn’t have any interest in listening to my explanation of what went wrong with the prior hitch.
by: Bill T. NE PA01/21/2015
I went on-line and have a very specific vehicle. I found what I think I needed & then called in. I got Jean P. & she was excellent.
She got me exactly what I needed. Hitch Receiver, Wiring Harnesses
for Lights & Brake controller, etc. She sent me an E-Mail with the specs on everything. She made it so easy, It was a No brainer.
For Quality, and Pricing, e-Trailer can't be beat. I'd use them again
anytime. Probably on e of the best Purchasing experiences I've ever had. No guesswork, No Games, It was a pleasure. Keep up the great Job!!! And, Thank you. Sincerely, Bill T. Sellersville, PA
25
105
Show More Reviews
See what our Experts say about this CURT Trailer Hitch
- Trailer Hitch Receiver and Wiring Harness For a 1972 Chevrolet K-20 Pickup With Step BumperI do see that a deepdrop rear step bumper was offered on your 1972 Chevrolet K-20 pickup. If this is what you have the Curt 3-Piece Trailer Hitch Receiver # C15511 is the receiver I recommend using. Otherwise the Curt Trailer Hitch Receiver # C14082 will fit the standard bumper which came on the K-20 or one of the aftermarket step bumpers that was often used as a replacement. We do have images on our product pages with both these installed so you can see how they will fit with their style...
view full answer... - Will Curt Trailer Hitch Fit with Flat Bed on 1984 Chevy K20 The top of the receiver for the Curt Trailer Hitch # C14082 is going to sit roughly 4" lower than the frame on your 1984 Chevy K20. I'm not sure what the dimensions of your flat bed are, but if the part of your flat bed that you're talking about is more than 4" lower than the frame on your pickup then it definitely won't fit. If it's less than 4" then you should be good to go!
view full answer... - Recommended Trailer Hitch Receiver For 1995 Ford F-250 W/ 37" Frame For Towing 6000lb TrailerFor your 1995 Ford F-250 with the 37" wide frame I recommend the Curt Trailer Hitch Receiver # 14001 as long as you have the standard bumper, or step bumper. This hitch has a 1000lb tongue weight rating and 10000lb trailer weight rating to accommodate the trailer you mentioned. If you have a deep drop bumper you will need the # BWHDRH25198 which fits your 37" frame perfectly, and has a 1600lb tongue weight rating and 16000lb trailer weight rating. I included videos of the products mentioned...
view full answer... - Recommended Hitch Receiver for a 1971 Chevrolet C/K Series Pick UpI do have a hitch receiver option for your 1971 Chevrolet C/K Series Pick Up however, none of which will protrude through the rear license plate. For a rear hitch receiver confirmed to fit your vehicle, I recommend using the Curt Trailer Hitch Receiver part # C14082 as this hitch receiver will provide you with a clean look and Class IV towing capacities up to 10,000 lbs if your vehicle is rated that high. If you are looking to tow a trailer, I also recommend the 4-Pole Hardwire Kit with...
view full answer... - Trailer Hitch Receiver Fit For 1995 Ford F-350 Cab & ChassisHappy to help, and there are a pair of trailer hitch receivers that are a fit for your 1995 Ford F-350 cab and chassis, so long as it has a 34 inch frame width from outside to outside, and I do recommend taking a quick measurement just to be sure. That said, with these two hitches, the difference is that one is a Class III hitch with a 6,000 lb towing/600 lb tongue weight capacity and the other being a Class IV hitch with a 10,000 lb towing/1,000 lb tongue weight capacity. So you can choose...
view full answer... - Recommended Trailer Hitch and Wiring for 1965 International TravelallSince there is no custom-fit hitch for your 1965 International Travelall, you will want to go with a universal hitch like the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-07. The # C14082 is not confirmed to fit your vehicle. The Draw-Tite hitch has a 2" receiver and fits vehicle frames up to 44". This is a weld-on hitch so we recommend taking it to a certified welder for installation. For wiring you can use the # C58345 which also comes with a mounting bracket. If...
view full answer... - 1987 F350 with 34 inch Frame Hitch RecommendationThe 34 inch frame like what you have is typically found on the cab and chassis models of trucks. The hitch confirmed to fit your 1987 Ford F350 with a 34 inch frame is the Curt hitch part # C14082.
view full answer... - Will Curt Trailer Hitch Fit a 2016 Fleetwood Bounder 36H MotorhomeI definitely understand where you're coming from, but I can assure you that we list the Curt Trailer Hitch Receiver # C14082 as a fit for your 2016 Fleetwood Bounder 36H because we've done our research and have confirmed it to fit the F-53 chassis on your motorhome. Sometimes hitches will fit multiple applications and this is one of those cases - so you can be confident you're getting a trailer hitch that fits your motorhome!
view full answer... - Will the Curt Hitch Part # C14082 Work with the Spare Tire on a 1986 Chevrolet C/K Series PickupI spoke to my contact at Curt about the Curt Trailer Hitch Receiver part # C14082 for your 1986 Chevrolet C/K Series Pickup and they informed me that as long as the spare tire is of the stock tire size then it will work with the hitch installed. If you are looking to tow a trailer you will also need a wiring harness and ball mount/hitch ball if you do not already have them. For a wiring harness that will give you a 4-way trailer connector at the rear of your truck, I recommend using the...
view full answer...
- Does the Curt #14082 Require Modification to Work with Under Bed Mounted Spare Tire?Yes. I've linked a picture of a Chevy C Series with the under-mounted spare tire to show you, but the Curt # C14082 will work with the stock spare tire mounting location on your 1971 C Series pickup and you won't need to make any modifications as long as your truck has 34" frame spacing. If your 1971 C10 has a frame with different width, please let me know and I can recommend a universal hitch that will work for your truck.
view full answer...
- Class V Hitch for 2003 GMC Savanah CutawayBuyers Products Class V hitch # 3371801102 fits the cutaway cab and chassis version of the 2003 GMC Savana Van. For the cargo and passenger van version their Class V hitch # 3371801100 is the correct fit. I am not sure which version of the base vehicle you have (nor could Buyer's Products confirm based on it having been made as a school bus) so what you can do to determine which hitch will fit is simply look at the frame under the van. If you refer to the photos of the two hitches you...
view full answer...
- Distance From Hitch Tube to End of Receiver of Curt Hitch C14082The distance from the crosstube to the very end of the receiver is 8 inches for the Curt Trailer Hitch Receiver # C14082.
view full answer... - Recommended Class V Hitch for 1975 International HD200The Curt # C15803 you referenced is only a fit for 2014-2018 Ram trucks so that isn't the correct fit. Because you have a 34 inch frame, I recommend the Buyers Products Class 5 Service Body Hitch Receiver - 2-1/2" # 3373018538 which measures end to end 44 inches but then you will weld brackets at your required fit. For that hitch with 9 inch brackets, I recommend # 3371801052. If you want to use a smaller hitch, there is a bolt on option in the Curt Trailer Hitch Receiver - Custom...
view full answer... - Will Curt Trailer Hitch Receiver for 1984 Chevy C/K Series Pickup Work with Brackets Under FrameThe trailer hitch options for a 1984 Chevrolet C/K Series Pickup all install in the same manor using holes on the underside of the frame. If there are any brackets present they would need to be removed and are most likely not factory therefore the hitch is not designed to work with them. I have attached a photo of the Curt Trailer Hitch Receiver part # C14082 close up so you can review fit.
view full answer...
- How Wide is Hitch Mounting Bracket of Curt Hitch part # C14082The side brackets of the Curt hitch part # C14082 are 9-3/4 inches long so you'd have the clearance needed to fit this on your frame since you have 10 available inches.
view full answer...
- Trailer Hitch Recommendation for 2019 Chevy Express 4500 Cutaway ChassisFor your 2019 Chevy 4500 Cutaway Chassis we have the Buyers Products part # 3371801102 as a confirmed fit. This is only option we have currently but it has great towing capacities at 12,000 lbs trailer weight and 1,200 lbs tongue weight.
view full answer... - Distance from Mounting Bracket to Top of Receiver on Curt Trailer Hitch # C14082The measurement from the top of the mounting bracket down to the top of the receiver tube measures 5 inches. Curt trailer hitch # C14082 is a custom fit hitch designed to fit the following vehicles: 1973 - 2000 Chevrolet C/K Series Pickup Cab and Chassis 1973 - 2000 GMC C/K Series Pickup Cab and Chassis 1973 - 1983 Ford F-100, F-150, F-250, F-350 Cab and Chassis 1984 - 1991 Ford F-150, F-250, F-350 Cab and Chassis 1992 - 1996 Ford F-250 and F-350 Cab and Chassis If you have a different...
view full answer... - Recommended Hitch for a 2011 Itasca Suncruiser 35P MotorhomeYes, there is and you are in luck because there is a custom fit option. The Curt Trailer Hitch item # C14082 will bolt directly to the frame of your 2011 Itasca Suncruiser 35P. This is a class IV hitch with a 2" receiver. It has a 10,000 lbs towing capacity and a 1,000 lbs maximum tongue weight. The Curt Trailer Hitch item # C14082 fits frames that are 34" wide. It also does require drilling as there are no predrilled holes for a hitch. If your frame is wider than 34" you will need to...
view full answer... - Will Curt Hitch C14082 for 1979 Chevy C/K Series Pickup Work with Spare TireYes, you'll be able to re-install the rear spare tire with the Curt Trailer Hitch Receiver part # C14082 in place on a 1979 Chevrolet C/K Series Pickup. I have attached for you below a photo of a truck with this same hitch and the spare tire installed.
view full answer...
- Curt Trailer Hitch Receiver # C14082 Tube Height From Mounting Flange For 1973 Ford F-100As we have not had a 1973 Ford F-100 in our shop to test fit the available receivers I can only give you the measurements from one of our receivers so that you can see where it will sit on your truck. The Curt Trailer Hitch Receiver # C14082 is 5" from the top of the bolt mounting flange to the top of the receiver tube. Also this will only fit frames that are 34" wide, that is from outside frame rail to outside frame rail.
view full answer...
- Curt Trailer Hitch Recommendation for 1980 Short Bed Chevy Truck with Standard BumperFor your 1980 Chevy truck with a short bed and a standard bumper the Curt hitch part # C14082 is a confirmed fit and would work well. Curt has confirmed the fit for us.
view full answer...
- 1990 Chevy C1500 Truck Frame Spacing to Fit Curt Trailer Hitch ReceiverHey Zack, thanks for reaching out! The Curt Trailer Hitch Receiver # C14082 has the bolt holes measuring 31-1/4" spacing from center to center. Your truck frame needs to measure 34" outside to outside for this to fit.
view full answer... - Trailer Hitch for a 1979 Chevy C-10 with Trailering Special PackageActually several of your pictures did make it through! What you have there is the standard/step bumper on your 1979 Chevy C-10. Deep drop bumpers, also called cowboy bumpers, drop way down. If your truck has an 8 foot bed you can use Curt trailer hitch # C14082. If you have a 6 foot bed you would need hitch # e88AR.. If you go with the Curt hitch then I also recommend etrailer ball mount kit # EBMK2416. It comes with a ball mount with a 3 inch rise/4 inch trop, a 2 inch ball, 2-5/16 inch...
view full answer...
- Bolt Hole Spacing of Curt Class IV Hitch Receiver 14082From side to side, the mounting holes measure 31-1/4 inches apart, center to center. All three sets of holes are the same distance apart. From rear to front, beginning at the rear of the vehicle the distance from the first set of holes to the second is 3-1/4 inches. From the second set to the third set is 2-3/4 inches. I've provided a diagram showing these measurements.
view full answer...
Do you have a question about this Trailer Hitch?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Updated by:
Adele M
Updated by:
Wilson B
Updated by:
Kristina F
Updated by:
Isabelle B
Video Edited:
Chris R
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
William
6/2/2023
Still great.